Hello! You can buy Storage system for EPS cables MS700 at website a-profi.shop at a low price. We deliver equipment worldwide.
MS700 – Storage system for EPS cables.
This device is used as a holder for electric power steering cables to EPS Controller MS561. The cables are intended for connection of particular EPS racks, columns and pumps. As far as 5 cables can be selected optionally and given for free when buying MS561, this system will be relevant for comfortable storage and easy use when conducting diagnostic and repair works of electric units.
Hello! You can buy set of fittings MS00553 at website a-profi.shop or at WhatsApp (+38-093-034-37-20) at a low price. We deliver equipment worldwide.
MS00553 – Set of fittings.
Description MS00553
Assignment: connection of a steering rack to a test bench.
Use: used for diagnostics of technical condition of a steering rack.
Features: minimum risk of mechanic damage in the place of fixing of a steering rack to a bench, including heavy operation modes; fittings and clamping plates are included in the set.
You can buy LOKI – a multi-function device for diagnostics of Tesla vehicles at website a-profi.shop or at fone +380930343720 (WhatsApp) at a low price.
LOKI – a multi-function device for diagnostics of Tesla vehicles.
LOKI has all the service functions necessary for repair and maintenance of the following Tesla models: Model S, Model X, and Model 3.
Performance capabilities of the multi-function device for Tesla diagnostics
Applicable for all Tesla models.
Navigation installation and setting.
Firmware updates.
Complete reconfiguration of Model S/X Tegra.
Complete reconfiguration of Model S/X Intel.
Partial reconfiguration of Model 3.
Reading and decoding of alert codes.
Erasing of service alert codes.
DTC reading from different ECUs and their subsequent decoding
DTC clearing from different ECU.
Reading of identifications from ECUs.
Reading of a pre-set PIN code with subsequent deactivation of Valet Mode.
Reading of a pre-set PIN code with subsequent deactivation of PIN to drive
Activation of Factory/Diagnostic/Developer Mode.
Cooling system draining and air purging.
Switching of vehicle systems to service mode.
ECUs reprogramming and VIN learning.
ECUs setting, adaptation, and calibration (radar sensor, door handles, charger port door, etc.)
Key Fob pairing to Model S.
Removing of special alert codes from BMS.
Equipment set LOKI
Module LOKI.
Cable LC001-CS – Cable CAN for Tesla Model S.
Cable LC002-LS – Cable LAN for Tesla Model S/X.
Cable LC003-CX – Cable CAN for Tesla Model SR, Model X.
Cable LC004-L3 – Cable LAN for Tesla Model 3.
Functions available by January, 2021
• Can be used for diagnostics of Tesla vehicles: Model S, Model X, Model 3;
• Navigation installation and setting: inclusive for firmware MS (tegra / intel),
MX (tegra / intel), M3;
• Firmware upgrade: available 2020.48;
• Complete change of vehicle configurations in Model S/X Tegra;
• Complete change of vehicle configurations in Model S/X Intel;
• Partial change of vehicle configurations in Model 3 before 2020.48
(Security Configuration presented separately);
• Alert codes reading and decoding;
• Alerts codes description;
• Service alert codes removal;
• DTC reading from different ECUs and their subsequent decoding;
• DTC clearing from different ECUs;
• Identifications reading from ECUs;
• Reading of a pre-set PIN code with subsequent deactivation of Valet Mode;
• Reading of a pre-set Pin code with subsequent deactivation of PIN to drive;
• Factory/Diagnostic/Developer Mode activation (on all firmware up to M3
2020.48);
• Switching vehicle systems to service mode;
• ECU reprogramming and VIN learn;
• ECUs setting, adaptation, and calibration (radar sensor, door handles,
charging port door, etc.);
• Removing special alert codes from BMS.
Available soon
Security Configuration Features (only for Model 3)
• Activation of any Autopilot versions;
• Performance Activation of Security Configuration (only for Long Range Dual
Motor, with PN last digits 980)
• Reconfiguration of Headlights and Direction Lights USA→EU.
• Activation of Premium Connectivity (Spotify, Youtube, e.t.c.)
Security Configuration is additional chargeable service allowing to expand the
capacity of device.
Loki requires special cable and software for work.
New Function Update in February:
• Crash data clearing from SRS
• Crash data clearing from TAS/EAS.
• Autopilot Firmware Update
• Update of Autopilot Firmware
• Radar Calibration for Autopilot 2.0, 2.5, 3.0 to the Models S/X/3.
• BMS (Battery Management System) operation.
• Some CAN modules operation
Technical characteristics LOKI
Net Weight, kg – 0,42 (weight of the LOKI module + all the cables included in the equipment set).
Hello! You can buy automotive scanner MaxiDAS DS808 at website a-profi.shop or at fone +38-093-034-37-20 (WhatsApp) at a low price.
MaxiDAS DS808, based on the Android operating system, is featured with an extensive coverage of OE-level diagnostics. Installed with a fast quad-core processor, DS808 offers maximum convenience and efficiency for your diagnosis and analysis. The intuitive user interface makes using the device effortless through a 7-inch LCD touchscreen that displays at 1024 x 600 quality.
Description:
Extensive vehicle coverage for more than 80 US, Asian and European vehicle makesExceptional OE-Level system coverage for all electronic systemsComplete capabilities for codes, live data, active test, ECU information, adaptation, matching, etc.Smart AutoVIN technology for identifying vehicles easilyAutomatic system and software updates with real-time push message notifications via Wi-FiInstant remote control tech support anytime, anywhereCloud-based MaxiFix online community provides a vast database of diagnostic and repair tips and proven filed fixesInteractive Data Logging sessions enable direct contact with Autel Technical Support for first-hand troubleshooting of diagnostic bugs and errorsOne-stop multitasking designed for ideal management of workshop operations to keep all data files, customer info, and vehicle records well organizedConvenient data management system for managing internal program applications and reviewing data
Hello! You can buy automotive scanner MaxiCheck MX808 at website a-profi.shop or at fone +38-093-034-37-20 (WhatsApp) at a low price.
MaxiCheck MX808 is your perfect companion, when it comes to ultra-portability. Installed with a fast quad-core processor, MX808 offers maximum convenience and swift diagnosis. The intuitive user interface makes using the device effortless through a 7-inch LCD touch screen that displays at 1024×600 quality.
Description
Read/clear codes for all available systems
Display live data in text, graph & analog for easy data review
Auto VIN technology can automatically identify the vehicle’s make, model and year information in no time
Reset Steering Angle Sensor (SAS)
Reset service mileage and service intervals
Relearn parking brake pad after replacement
Support forced DPF regeneration and adjusting injectors
Designed for towing vehicles and quad weight up to 3 tons using a winch. Instruction An anchor is installed in the ground; A winch cable is connected to it; The winch is turned on; A car or quadrocycle is pulled out of a pit, dirt or loose ground. Here you can find other equipment forRead More
Anchor for winch - 70 $
Designed for towing vehicles and quad weight up to 3 tons using a winch.
Instruction
An anchor is installed in the ground;
A winch cable is connected to it;
The winch is turned on;
A car or quadrocycle is pulled out of a pit, dirt or loose ground.
Order nozzle for repair shock absorbers for repair of shock absorber struts at a low price anywhere in the World on the site a-profi.shop.
Nozzle for repair shock absorbers
Capabilities of nozzle for repair shock absorbers
To pump gas (nitrogen) into the rack (shock absorber) – indiscriminately.
Add oil to the rack (shock absorber) – indiscriminately.
Change the oil in the rack (shock absorber) – indiscriminately.
Available sizes of nozzles that fit all possible diameters of shock absorber rods:
11 mm, 12.5 mm, 13 mm, 14 mm, 15 mm, 16 mm, 18 mm, 20 mm, 22 mm, 25 mm, 28 mm, 30 mm.
Nozzle classes:
Econom class - business in a car service for a penny.
Standart class - perfect value for money.
Premium class - additional equipment and improved performance.
The principle of operation of the equipment
The shock absorber strut is designed in such a way that by injecting gas into the inside of the cylinder, we increase the internal pressure, which extrudes the rod and expands the gland from the inside. The result is increased tightness of the structure.
Thanks to the equipment you can:
Pump nitrogen into the shock absorber without disassembling it;
Add oil to the hydraulic system of the shock absorber strut;
Perform a complete oil change without laborious debriefing.
Also, the equipment makes it possible to monitor the level of oil pressure in the shock absorber strut, timely detect damage and eliminate them. Thanks to this, the motorist saves on overhaul and ensures a comfortable and safe ride, and the service station get additional profit.
Hello! You can buy Tester for car alternators and voltage regulators MS016 at website a-profi.shop or at fone +38-093-034-37-20 (WhatsApp) at a low price.
MS016 – Tester for car alternators and voltage regulators.
MS016 is a compact, multifunctional device for quick and quality diagnostics of automotive alternators and starters directly in a car, and voltage regulators separately from alternators.
Detailed description MS016
MS016 Tester allows making a health assessment of 12V/24V/48V alternators and starters directly in the car. Special cables for connection to the alternator (voltage regulator) are included in the equipment set which makes the diagnostic procedure shorter and easier. The device can test all types of modern voltage regulators. The tester takes CAN- and LIN-bus readings in real-time mode and is equipped with a dual-channel oscilloscope.
Advantages:
- diagnostics of alternators and starters directly in a car;
- diagnostics of voltage regulators separately form alternators;
- special diagnostic cables to ensure the accuracy of the alternator (voltage regulator) connection are included in the equipment set;
- powerful microcontroller and a large amount of RAM;
- capable of receiving/transmitting LIN, CAN and waveform signals;
- dual-channel oscilloscope;
- compact size;
- convenience and ease of use;
- firmware updates are available.
Technical characteristics MS016:
Dimensions (l×w×h), mm: 140×82×16
Weight, kg: 0,3
Supply voltage, v: from 10 to 60 в
Touch screen: ips 4.3″ capacitive touch
Software update: yes
The nominal voltage of tested alternators, v: 12, 24, 48
Alternator types
«l/fr», «sig», «rlo», «rvc», «c korea», «p-d», «com» («lin», «bss»), «c japan»,
«i-eloop»..
Tested parameters
– stabilizing voltage;
– voltage regulator current consumption;
– test lamp: fr (load on voltage regulator).
for com voltage regulators:
– id;
– protocol;
– data exchange rate;
– voltage regulator type;
– errors.
Accuracy of voltage measurement, v: 0,01
The nominal voltage of tested starters, v: 12, 24, 48
Hello! You can buy tester for diodes & rectifiers MS021 at website a-profi.shop or at fone +38-093-034-37-20 (WhatsApp) at a low price.
MS021 tester enables to evaluate technical condition of a rectifier in the automotive alternator, as well as of diodes separately. The device is user-friendly, light-weighted and has small dimensions. It has been designed to meet the requirements of auto service stations.
MS021 Tester is intended to test the performance of diode bridges in automotive alternators as well as of diodes separately.
The device detects:
- short-circuit;
- breakdown;
- open circuit;
- degradation of the diode (loss of its nominal characteristics);
- quality of contact between the diode and the conductive busbars;
- type and characteristics of the avalanche diode, which allows to select the necessary diode to replace the failed one.
Advantages:
- the diode is tested with an alternate current under simulated real operational conditions to ensure its proper health assessment;
- the device tests rectifiers and diodes of all types;
convenience and ease of use;
- use of the device does not require the operator to have any special knowledge about the parameters and characteristics of the diodes;
- color indication to notify about fault detection;
the device is equipped with a special system for testing diagnostic cables;
- compact size.
Technical characteristics MS021:
Dimensions, (L×W×H), mm - 219×214×80
Weight, kg - 2
Supply voltage, V - 230/110
Supply frequency, Hz - 50/60
Supply type - Single-phase electric power
Consuming power, W - 40
Current strength of diode test, A - 0,9
Voltage on the contact probes of the device (AC), V - 30
Hello! You can buy slide hammer oil seals extractor MS00058 at website a-profi.shop at a low price. We deliver equipment worldwide.
MS00058 – Slide hammer oil seals extractor
Features MS00058
- easy removal of seals at a depth of 400 mm, inside diameter of a seal is 20-30 mm;
- tool prevents hydraulic cylinder from mechanic damage and deformation;
- сhangeable tip MS00100 for seals of inside diameter 30-40 mm is sold separately.
You can buy 1 Stage Engine Revitalizant for gasoline and diesel engine at website a-profi.shop or at WhatsApp (+38-093-03-43-720).
1 Stage Engine Revitalizant for gasoline and diesel engine. Price: 32,27 $
1 Stage Engine Revitalizant for gasoline and diesel engine is a 1-step engine treatment that rebuilds metal and protects worn metal from future wear. One 27ml bottle contains enough active ingredient for a complete 100% (RF100) cycle of revitalization for an automobile engine. The difference between this product and 1 Stage Maximum Atomic Metal Conditioner is this product is only the raw, active ingredient – Revitalizant – in gel form. Revitalizant has been independently tested and proven to increase compression, decrease fuel consumption, increase horsepower, and reduce toxic emissions.
No matter how well a car is maintained, high heat and friction cause a car’s engine to become worn, scratched, and mis-shaped over time. Adding just a tube of XADO 1 Stage Engine Revitalizant to your engine oil rebuilds worn engine metal and coats the rebuilt metal at the friction points with a self-regulating layer of ceramic-metal to prevent future wear. Unlike other engine treatments that must be added during every oil change, 1 Stage Engine Revitalizant needs to be added only ONCE for 62,000 miles of protection.
XADO’s innovative patented nano-technology is the result of 20 years of research and development. When added to an automobile’s engine oil, Revitalizant rebuilds worn engine metal at the atomic level, reversing wear, restoring engine geometry, and coating engine metal with a layer of ceramic-metal to protect against future wear. Revitalizant is activated by high-heat and friction, so it only repairs metal at high-friction points where metal wear occurs. Revitalizant leaves crank-cases and non-friction metal unaffected. The protective layer of Revitalizant does not cake, flake, or alter oil viscosity. This makes it safe to use in even the most sensitive vehicles. 1 Stage is compatible with all motor oils, from full-synthetic to mineral. XADO’s Revitalizant technology has been independently tested and proven to work.
Buy equipment for repairing shock absorber struts at a low price on a-profi.shop
The company offers unique equipment for repairing shock absorber struts (12 nozzles of the Premium class), which allows you to restore the factory characteristics of shock absorbers using the technology of the manufacturer.
Premium class: additional equipment and improved performance.
Equipment capabilities:
1. To pump gas (nitrogen) into the rack (shock absorber) – indiscriminately.
2. Add oil to the rack (shock absorber) – indiscriminately.
3. Change the oil in the rack (shock absorber) – indiscriminately.
Package bundle:
- 12 special nozzles of the premium class;
- Pressure gauge;
- 2 the high pressure hose;
- Necessary adapters;
- Instruction;
- Metal boxing.
Available sizes of nozzles that fit all possible diameters of shock absorber rods:
11 mm, 12.5 mm, 13 mm, 14 mm, 15 mm, 16 mm, 18 mm, 20 mm, 22 mm, 25 mm, 28 mm, 30 mm.
The principle of operation of the equipment:
The shock absorber strut is designed in such a way that by injecting gas into the inside of the cylinder, we increase the internal pressure, which extrudes the rod and expands the gland from the inside. The result is increased tightness of the structure.
Thanks to the equipment you can:
- Pump nitrogen into the shock absorber without disassembling it;
- Add oil to the hydraulic system of the shock absorber strut;
- Perform a complete oil change without laborious debriefing.
Also, the equipment makes it possible to monitor the level of oil pressure in the shock absorber strut, timely detect damage and eliminate them. Thanks to this, the motorist saves on overhaul and ensures a comfortable and safe ride, and the service station get additional profit.
Buy equipment for repairing shock absorber struts at a low price on a-profi.shop
The company offers unique equipment for repairing shock absorber struts (10 nozzles of the Premium class), which allows you to restore the factory characteristics of shock absorbers using the technology of the manufacturer.
Premium class: additional equipment and improved performance.
Equipment capabilities:
1. To pump gas (nitrogen) into the rack (shock absorber) – indiscriminately.
2. Add oil to the rack (shock absorber) – indiscriminately.
3. Change the oil in the rack (shock absorber) – indiscriminately.
Package bundle:
- 10 special nozzles of the premium class;
- Pressure gauge;
- 2 the high pressure hose;
- Necessary adapters;
- Instruction;
- Metal boxing.
Available sizes of nozzles that fit all possible diameters of shock absorber rods:
11 mm, 12.5 mm, 13 mm, 14 mm, 15 mm, 16 mm, 18 mm, 20 mm, 22 mm, 25 mm, 28 mm, 30 mm.
The principle of operation of the equipment:
The shock absorber strut is designed in such a way that by injecting gas into the inside of the cylinder, we increase the internal pressure, which extrudes the rod and expands the gland from the inside. The result is increased tightness of the structure.Equipment for repairing shock absorber struts at work
Thanks to the equipment you can:
- Pump nitrogen into the shock absorber without disassembling it;
- Add oil to the hydraulic system of the shock absorber strut;
- Perform a complete oil change without laborious debriefing.
Also, the equipment makes it possible to monitor the level of oil pressure in the shock absorber strut, timely detect damage and eliminate them. Thanks to this, the motorist saves on overhaul and ensures a comfortable and safe ride, and the service station get additional profit.
Hello! You can buy Triumph 6 injector cleaning equipment at website a-profi.shop at a low price. We deliver equipment worldwide.
The equipment for cleaning injector he Triumph 6 works on the principle of hydrodynamic cavitation. How it works? Let’s figure it out:
- The injector needle in a fluid stream moves at high speed. It has many bulges on its surface. Behind them, a vacuum is formed during the movement;
- As a result of environmental pressure, the vacuum is divided into a huge number of microscopic bubbles;
- Bubbles collapse, forming microexplosions. Their energy also eliminates varnish deposits that impede the full operation of the injector.
Technology benefits:
1. The cavitation zone is formed directly in the injector channel, due to which the nozzle, fuel channel and valve needle are cleaned. As a result, maximum efficiency is achieved in removing varnish deposits from the workspace of the part.
2. Injectors made of ceramic or teflon can be cleaned. The phenomenon of hydrodynamic cavitation interacts much more carefully with the material than the same ultrasonic waves.
3. Flushing in one step. This greatly speeds up the work and, therefore, increases the profit of the workshop.
All three of these items are not performed by ultrasound equipment.
Functionality Triumph 6:
Gasoline injector cleaning: Europe / Japan / America
Cleaning gasoline injectors with longitudinal fuel injection / lateral fuel injection / monoinjection
Simultaneous measurement of the resistance of a group of injectors
Checking the mechanics (quality of the spring)
Dynamic check consumption
Auto cleaning mode
Manual cleaning mode
Turbo cleaning mode
Short circuit protection
Protection against deformation of the needle and seat when closing the injector (anti-shock system)
Idle valve cleaning mode
Injector leak test
Injector cleaning indiscriminately
Fluid pressure adjustment
Tank pressure indicator
Specifications:
Number of nozzle seats: 6
Injector resistance: 2-30 ohms
Cleaning time: 30 minutes
Mains voltage: 220 V
Tank capacity: 700 ml
Cleaning fluid consumption: 80-150 ml
Pressure in modes: 0-5 at.
Dimensions: 370х295х333 mm
The weight: 12 kg
Guarantee: 24 months
Hello! You can buy Triumph 4M injector cleaning equipment at website a-profi.shop at a low price. We deliver equipment worldwide.
Equipment for cleaning injectors Triumph 4M works on the principle of hydrodynamic cavitation. How it works? Let’s figure it out:
- The injector needle in a fluid stream moves at high speed. It has many bulges on its surface. Behind them, a vacuum is formed during the movement;
- As a result of environmental pressure, the vacuum is divided into a huge number of microscopic bubbles;
- Bubbles collapse, forming microexplosions. Their energy also eliminates varnish deposits that impede the full operation of the injector.
Technology benefits:
1. The cavitation zone is formed directly in the injector channel, due to which the nozzle, fuel channel and valve needle are cleaned. As a result, maximum efficiency is achieved in removing varnish deposits from the workspace of the part.
2. Injectors made of ceramic or teflon can be cleaned. The phenomenon of hydrodynamic cavitation interacts much more carefully with the material than the same ultrasonic waves.
3. Flushing in one step. This greatly speeds up the work and, therefore, increases the profit of the workshop.
All three of these items are not performed by ultrasound equipment.
Functionality Triumph 4M:
Gasoline injector cleaning: Europe / Japan / America
Cleaning gasoline injectors with longitudinal fuel injection / lateral fuel injection / monoinjection
Simultaneous measurement of the resistance of a group of injectors
Checking the mechanics (quality of the spring)
Dynamic check consumption
Auto cleaning mode
Manual cleaning mode
Turbo cleaning mode
Short circuit protection
Protection against deformation of the needle and seat when closing the injector (anti-shock system)
Idle valve cleaning mode
Injector leak test
Injector cleaning indiscriminately
Fluid pressure adjustment
Tank pressure indicator
Specifications:
Number of nozzle seats: 4
Injector resistance: 2-30 ohms
Cleaning time: 30 minutes
Mains voltage: 220 V
Tank capacity: 700 ml
Cleaning fluid consumption: 80-120 ml
Pressure in modes: 0-5 at.
Dimension: 370х295х333 mm
The weight: 12 kg
Guarantee: 24 months