suprfury./com

i'm occasionally here

[mudz]

made using final cut pro x. in between meetings.

[mudz]

Optware: Transmission

SSH to your NAS. Use ipkg to install transmission. Do an ipkg update first.

ipkg install transmission

sleep 5

Create necessary file for transmission. replace /mnt/disk1/tmp to whatever working folder that you are using in your NAS.

/opt/bin/transmission-daemon -g /mnt/disk1/tmp/torrents/.config/transmission-daemon killall transmission-daemon sleep 2

I use nano to edit the config file. Install nano via 'ipkg install nano'. Edit the config file.

nano /mnt/disk1/tmp/.config/transmission-daemon/settings.json

Take note on the importants. refer to the complete list at https://trac.transmissionbt.com/wiki/EditConfigFiles

blocklist-url: String (default =  http://www.example.com/blocklist)

blocklist-enabled: Boolean (default = false)

download-dir: String (default = default locations)

rpc-whitelist: String (Comma-delimited list of IP addresses. Wildcards allowed using '*'. Example: "127.0.0.*,192.168.*.*", Default: "127.0.0.1" )

rpc-whitelist-enabled: Boolean (default = true)

rpc-port: Number (default = 9091)

To run transmission

/opt/bin/transmission-daemon -g /mnt/disk1/tmp/.config/transmission-daemon

Launch your browser and point to your NAS_IP:9091. Done.

Credit:http://tomatousb.org/tut:how-to-set-up-nas-optware-etc-for-total-noobs#6

[mudz]

[mudz]

[mudz]

OpenWRT: DynDNS

From the webgui, click System > Software. Update the lists.

Find 'dns'. Install 'luci-app-ddns'. Once finish, click Services > Dynamic DNS.

Change the 'Force update every' to a shorter period, to 'force' it for the first time. Once your dyndns updated, change it back. Done.

[mudz]

OpenWRT: Wifi

Go to Wireless Security to configure the security part.

[mudz]

OpenWRT: Change LAN subnet

This will change your OpenWRT IP address, and update the DHCP scope accordingly.

[mudz]

OpenWRT: Change default DNS to a better one

[mudz]

Configure OpenWRT for UNIFI

Assuming you have a working OpenWRT box. Objective is to 1) configure VLAN 500 (data) and 600 (IPTV) in Port 1 (WAN). 2) configure WAN to use PPPoE and 'dial' UNIFI and 3) configure port 5 as IPTV.

Login to OpenWRT then tab Network > Switch. Refer below:

Save & apply. Then tab Network > Interface. At WAN, click Edit. Change Protocol to PPPoE and confirm protocol change. Click Save & apply.

Key in UNIFI username and password and leave the rest as default. Click Physical settings and choose VLAN interface eth0.500.

Save & apply.

Plug in the connection from BTU to WAN port. Go back to interface and click Connect. You should achieve objective 1 and 2.

Now go back to Interface and click Add new interface at the bottom of the page.

Save & apply. Connect your hypp.tv box to port 5 (LAN port 4). Done.

[mudz]

Flash 1043ND to OpenWRT

Download latest OpenWRT build for 1043ND (Backfire). 1043ND is using Atheros 71xx chip.

http://downloads.openwrt.org/ > backfire/10.03.1/ar71xx/ find 1043nd. The current build as when this guide was written as below:

http://downloads.openwrt.org/backfire/10.03.1/ar71xx/openwrt-ar71xx-tl-wr1043nd-v1-squashfs-factory.bin

Unplug WAN port and use port 2 or 3.

Login to 1043ND webgui and upgrade the firmware using above file (*.bin). Wait until reboot.

Default subnet for OpenWRT is 192.168.1.0/24. Keep ping-ing to 192.168.1.1 to check when it is up. Point your browser to 192.168.1.1.

Default username is root, without password.

Done. Part 1.

[mudz]

boroi tapi fit? on steroid ke oi?

[mudz]

hoi keeper boleh tolong lompat sikit tak? takkan tunggu bola sampai depan tangan kot @t4mb0 @arhafiz @shukrans

[mudz]

what's wrong #harimaumalaya ?

[mudz]

proud wif harimau muda performance! #fb

[mudz]

RT @GreenPois0n_JB: BREAKING: Confirmed ! Mac OS X Lion Coming Tomorrow !! http://bit.ly/qH7Mao

[mudz]

“@syerrylina: ayam penyet tapau-ed. skrg mahu cari tempe. ahh... so the jawa! *hi @mudzao!” runs in the blood, hahaha

[mudz]

you're not a saint, so don't act like one #fb