#dbot

[thpsd]

[hulnews]

Namami Gange Project Phase-2 to Begin in 2022, Bidding Process to Start in Three Months

Namami Gange Project Phase-2 to Begin in 2022, Bidding Process to Start in Three Months

[ad_1]

The bidding process for projects under the second phase of the Namami Gange mission will start in the next three months, Director General of the National Mission for Clean Ganga Rajiv Mishra said on Tuesday.

The funding for the second phase was approved by the World Bank last week, and it will kickstart after the phase-1 ends on December 31, 2021, a statement by the NMCG said.

For…

View On WordPress

[ckpcity]

2022 में नमामि गंगे परियोजना चरण -2, तीन महीने में शुरू होने वाली बोली प्रक्रिया

2022 में नमामि गंगे परियोजना चरण -2, तीन महीने में शुरू होने वाली बोली प्रक्रिया

नमामि गंगे मिशन के दूसरे चरण के तहत आने वाली परियोजनाओं के लिए बोली प्रक्रिया अगले तीन महीनों में शुरू होगी, मंगलवार को नेशनल मिशन फॉर क्लीन गंगा के महानिदेशक राजीव मिश्रा ने कहा।

एनएमसीजी के एक बयान में कहा गया है कि दूसरे चरण के लिए फंडिंग को पिछले सप्ताह वर्ल्ड बैंक ने मंजूरी दे दी थी और 31 दिसंबर 2021 को चरण -1 समाप्त होने के बाद यह किकस्टार्ट होगा।

अगले चरण के लिए, भारत सरकार की ओर से…

View On WordPress

[completely3d-blog]

3 hours 58 minutes 1,0mm nozzle 0,4 layer The fake #titanextruder is keeping up with this bad dog and the small stepper motor is warm to touch.. . . . . #cbot #corexy #hbot #dbot #mksbase #reprap #smoothieware #3dprint #3dprinting #3dprinter #3ddesign #vase #3ddruck #rigidbot #maker #diy #3ddrunker (at Navarre, Florida)

[completely3d-blog]

Wohh I woke up to a print that stopped because of my filament breaking. The biggest nozzle I printed with up to this point was the 0,6 volcano nozzle. So I put in the 1,0 mm nozzle sliced it with slic3r Prusa Edition and this is what I got. It is printing the support on the outside madly sick and then the inside is printing two layers. The print is turning out beautiful on the inside, the support on the outside looks crazy and it seems like it's wasting a ton of material So What! This is actually the first time I printed ABS or with the 1,0mm nozzle on this C-Bot... 4hr print instead of 13 hr with 0,4mm! . . #cbot #corexy #hbot #dbot #mksbase #reprap #smoothieware #3dprint #3dprinting #3dprinter #3ddesign #vase #3ddruck #rigidbot #maker #diy #3ddrunker #valcanonozzel (at Navarre, Florida)

[completely3d-blog]

Lamp #2 . . . . . #cbot #corexy #hbot #dbot #mksbase #reprap #smoothieware #3dprint #3dprinting #3dprinter #3ddesign #vase #lampshades #lamps #3dlamps (at Navarre, Florida)