How To Setup Netgear EX6150 AC1200 Extender
You can use your extender in extender mode or in access point mode. In extender mode, your extender repeats the signals from your Wifi router. After initial setup, the best location for the extender is about halfway between your router and the area with a poor WiFi signal. The extender must be within the range of your wifi router network. In access point mode, your extender creates a new WiFi hotspot by using a wired Ethernet connection.
NETGEAR WiFi Mesh Range Extender EX6150 - Coverage up to 1200 sq. ft. and 20 Devices with AC1200 Dual Band Wireless Signal Booster & Repeater (up to 1200Mbps Speed), Plus Mesh Smart Roaming. In this article we will provide a step-by-step procedure on how to configure the Access Point functionality of an EX6150 to boost the Wi-Fi signal. Go to the website and read an article. We will guide you each and every step and setup your EX6150–AC1200 extender properly.
Setp EX6150 Extender in Extender Mode
1. Set the access point/extender switch to extender.
2. For initial setup, place your extender in the same room as your Wifi router.
3. Plug the extender into an electrical outlet.
Wait for the power LED to light green. This might take up to 2 minutes. If the power LED doesn't have the power ON/Off button on the extender.
Continue with installation, using one of these methods:
4. To connect your extender using WPS, see the following section.
Note:- WPS does not support WEP network security. If you are WEP security, you might use the Netgear installation assistant.
Setup EX6150 extender to your WiFi Network using WPS
WiFi Protected Setup lets you join a secure Wifi network without selecting the network name and entering the password.
1. Press the wps button on the wps button on your router.
2. Within two minutes, press the WPS button on your router. The wps LED on the extender lights solid green, the router Link LED lights, and the extender connects to your Wifi network.
Note:- If your router supports the GHz band and your extender won't connect that band, repeat the WPS process.
3. Unplug the extender and move it to a new location that is about halfway between your router and the area with a poor router WiFi signal. The extender must be within the range of your Wifi router network.
4. Plug the extender into an electrical outlet and wait for the Power LED to light green.
5. Use the router Link LED to find a spot where the extender to router connection is optimal.
6. If the router LED doesn't light amber or green, plug the extender into an outlet closer to the router and try again.
7. Connect your wifi-enabled computer or mobile device to the Wifi network.
Your extender uses the same Wifi name as your router, based on the Wifi band that it connects to first.
Connect the EX6150 extender to your wifi network using the Netgear installation assistant
1.The installation assistant guides you through the steps to connect your extender to your WiFi network.
.wifi. On your wifi-enabled computer or mobile device, join the extender wifi network Netgear_Ext.
Note:-Netgear_EXT is the extender's default wifi network.
.Ethernet. Use an Ethernet cable to connect the ethernet port on the extender to an ethernet port on your enabled computer.
when your Wifi-enabled computer or mobile device connects, the Client Link LED lights.
2. Launch a web browser and visit www.mywifiext.net. The netgear installation assistant displays.
3. Follow the prompts to connect your extender to your wifi network.
The Router Link LED lights when the extender connects to the router wifi network.
4. Unplug the extender and move it to a new location about halfway between your router and the area with a poor WiFi signal.
The extender must be within the range of your WiFi router network.
5. Plug the extender into an electrical outlet and wait for the Power LED to light green.
6. Use the Router Link LED to find a spot where the extender-to-router connection is optimal.
7. If the Router Link LED doesn't light amber or green, plug the extender into an outlet closer to the router and try again.
Setup EX6150 extender as an access point
You can use your extender as a WiFi access point, which creates a new WiFi hotspot by using a wired Ethernet connection.
1. Set the Access Point/Extender switch to Access Point.
2. Plug the extender into an electrical outlet. The Power LED lights green. If the Power LED doesn't light, press the Power button.
3. Connect a computer or mobile device to the extender using a WiFi or Ethernet connection:
Wifi. On your WiFi-enabled computer or mobile device, join the extender WiFi network NETGEAR_EXT.
Note: NETGEAR_EXT is the extender's default WiFi network.
When your WiFi-enabled computer or mobile device is connected to the extender, the Client LED lights.
Ethernet. Use an Ethernet cable to connect the Ethernet port on the extender to an Ethernet port on your computer.
4. Launch a web browser and visit www.mywifiext.net. The NETGEAR installation assistant displays.
5. Use an Ethernet cable to connect an Ethernet port on your router to the extender's Ethernet port.
Return to the NETGEAR installation assistant and follow the prompts to finish setting up your extender as an access point.
Still, in doubt, Need Expert advice, consider getting in touch with our experts. We are always ready and willing to help you out to solve your problem. You can get in touch by calling on our toll-free number +1-888-245-4797, or through live chat as well as email.
