#hg8245a

[thunderlinkcom]

GPON ONT Service Profile Configuration--display ont-srvprofile gpon bound-info

display ont-srvprofile gpon bound-info

Function

This command is used to query the bound information about a specified GPON ONT service profile, including the position of the GPON port the ONT whcih binds the profile related to, and the ONT ID.

Format

display ont-srvprofile gpon bound-info { profile-id profile-id | profile-name profile-name }

Parameters

Parameter

Description

Value

profile-id profile-id

Queries the bound information about the GPON ONT service profile of the specified ID.

Numeral type. Range:

SCUL/SCUN/SCUK/SCUB/SCUF: 0-8192

SCUH: 0-8192

MCUD/MCUD1: 0-1024

profile-name profile-name

Queries the bound information about the GPON ONT service profile of the specified name.

Character string type, a string of 1-32 characters.

Modes

Privilege mode, diagnose mode,  ONT,  HG8245H,  HG8245A

Level

Operator level

Usage Guidelines

In the privilege mode or global config mode, run the diagnose command to enter the Diagnose mode.

Run the display xpon global-config command to query the status of the bound xPON profile modification function. The GPON ONT service profile which has been bound by ONT cannot be modified when the bound xPON profile modification function is disabled. If you need to modify the bound profile, do as follows:

Run the xpon modify-bound-profile command to enable the bound xPON profile modification function of the bound GPON ONT service profile.

Run the ont modify(profile-mode) command or the ont delete command to unbind the ONT and GPON ONT service profile.

Example

To query the bound information of GPON ONT service profile 10, do as follows:

huawei#display ont-srvprofile gpon bound-info { profile-id<K>|profile-name<K> }:profile-id { profile-id<U><0,8192> }:10                                                                                                                                      Command:                                                                                display ont-srvprofile gpon bound-info profile-id 10                              ---------------------------------------------------------------------          F/S/P       ONT List  ---------------------------------------------------------------------          0/ 1/0      0,2  0/ 2/0      3-5  0/ 4/0      5-6,8  ---------------------------------------------------------------------

System Response

The system displays the queried result when the command runs successfully.

The following table describes the parameters in response to the command.

For more information about the error message that the system displays against a command entered with incorrect syntax,

Parameter

Description

F/S/P

Indicates the shelf ID, slot ID, and port ID of the ports the ONTs which bind GPON ONT service profile related to.

ONT List

Indicates the list of the ONTs which bind GPON ONT service profile.

[thunderlinkcom]

ont-profile modify(distributing-mode)

ont-profile modify(distributing-mode)

Function

This command is used to modify an ONT capability set profile. When the configuration data of a profile does not meet the requirements, run the command to modify the profile.

Format

ont-profile modify { profile-id profile-id | profile-name profile-name }

Parameters

Parameter

Description

Value

profile-id profile-id

Indicates the ID of the ONT capability set profile. It identifies a capability set profile uniquely. When you need to modify a capability set profile by profile ID, use this parameter.

Numeral type. Range: 17-128.

profile-name profile-name

Indicates the name of the ONT capability set profile. When you need to modify a capability set profile by profile name, use this parameter.

Character string type, a string of 1-63 characters.

Modes

Global config mode, Diagnose mode, HG8245H,  HG8245A

Level

Operator level

Usage Guidelines

In the privilege mode or global config mode, run the diagnose command to enter the Diagnose mode.

You are recommended to use this command in the global config mode.

The system default profiles include the multi-dwelling unit (MDU) profile, and the profile for the common ONTs. They are numbered from 1 to 16. The reserved profile numbers of the 16 profiles are null and can be added according to requirements. Currently, the system has four default ONT capability set profiles. The default profiles cannot be modified or deleted.

The profile bound with an ONT cannot be modified or deleted.

Example

To modify the mapping mode of ONT capability set profile 17 to 802_1pPRI, do as follows:

huawei(config)#ont-profile modify { profile-id<K>|profile-name<K> }:profile-id { profile-id<U><17,128> }:17  Command:          ont-profile modify profile-id 17  Press 'Q' or 'q' to quit input                                                 >  Are you sure you want to set the number of POTS ports to auto-adaptive? (y/n) [n]:y                                                                      Are you sure you want to set the number of ETH ports to auto-adaptive? (y/n) [n]:y                                                                       >  Are you sure you want to set the number of VDSL ports to auto-adaptive? (y/n) [n]:y   >  TDM port type<1-E1,2-T1> [1]:                                                 >  TDM service type<1-TDMoGEM> [1]:                                             >  Number of TDM ports<0-8> [0]:                                                 >  Number of MOCA ports<0-8> [0]:                                               >  Are you sure you want to set the number of CATV UNI ports to auto-adaptive? ( y/n) [n]:                                         >  Number of CATV UNI ports<0-8> [0]:                                           >  Mapping mode<1-VLANID, 2-802_1pPRI, 3-VLANID_802_1pPRI, 4-PORTID,               5-PORTID_VLANID, 6-PORTID_802_1pPRI, 7-PORTID_VLANID_802_1pPRI,   9-IPTOS, 10-VLANID_IPTOS> [1]:2                                               >  The type of flow control<1-PQ, 2-GEMPORT-CAR, 3-FLOW-CAR> [1]:                Modifying an ONT profile succeeded

System Response

The system displays the message "Modifying an ONT profile succeeded" after an ONT capability set profile is modified successfully.

The following table describes the parameters in response to this command. Indicates whether to set the number of plain old telephone service (POTS) ports to adaptive. Indicates whether to set the number of Ethernet ports to adaptive. Indicates whether to set the number of VDSL ports to adaptive. Indicates whether to set the number of CATV UNI ports to adaptive. Indicates the mapping mode between the service flow and the GEM port.

For more information about the error message that the system displays against a command entered with incorrect syntax,

Parameter

Description

Are you sure you want to set the number of POTS ports to auto-adaptive? (y/n) [n]:

y: Sets the number of POTS ports to adaptive so that the number of POTS ports is set based on the actual number on the ONT

n: Sets the number of POTS ports to non-adaptive so that the number of POTS ports is set in a subsequent step.

Number of POTS ports

Indicates the number of the POTS ports. The configured value must be the same as the number of the actual POTS ports.

Are you sure you want to set the number of ETH ports to auto-adaptive? (y/n) [n]:

y: Sets the number of Ethernet ports to adaptive so that the number of Ethernet ports is set based on the actual number on the ONT

n: Sets the number of Ethernet ports to non-adaptive so that the number of Ethernet ports is set in a subsequent step.

Number of ETH ports

Indicates the number of the ETH ports. The configured value must be the same as the number of the actual ETH ports.

Are you sure you want to set the number of VDSL ports to auto-adaptive? (y/n) [n]:

y: Sets the number of VDSLt ports to adaptive so that the number of Ethernet ports is set based on the actual number on the ONT

n: Sets the number of VDSL ports to non-adaptive so that the number of Ethernet ports is set in a subsequent step.

Number of VDSL ports

Indicates the number of the VDSL ports. The configured value must be the same as the number of the actual VDSL ports.

TDM port type

Indicates the TDM port type. It can be E1 or T1 type.

TDM service type

Indicates the TDM service type. It can be TDMoGEM type only.

Number of TDM ports

Indicates the number of the TDM ports. The configured value must be the same as the number of the actual TDM ports.

Number of MOCA ports

Indicates the number of the MOCA ports. The configured value must be the same as the number of the actual MOCA ports.

Are you sure you want to set the number of CATV UNI ports to auto-adaptive? ( y/n) [n]:

y: Sets the number of CATV UNI ports to adaptive so that the number of CATV UNI ports is set based on the actual number on the ONT

n: Sets the number of CATV UNI ports to non-adaptive so that the number of CATV UNI ports is set in a subsequent step.

Number of CATV UNI ports

Indicates the number of the CATV UNI ports. The configured value must be the same as the number of the actual CATV UNI ports.

Mapping mode

In the single bridge mode, it can be set to mapping based on VLAN, mapping based on 802.1p priority, or mapping based on VLAN+802.1p priority. By default, the mapping mode is mapping based on VLAN.

In the multi-bridge mode, it can be set to mapping based on port ID.

ONT mapping modes include the following categories: These 4 mapping categories are mutually exclusive on the same ONT, but mapping modes of the same category can be configured on the same ONT. For example, if the ONT mapping mode is set to mapping based on VLAN, the mapping between the GEM port and service flow can be set to mapping based on VLAN, mapping based on 802.1p priority, or mapping based on VLAN+802.1p priority.

Category 1: mapping based on VLAN, mapping based on 802.1p priority, and mapping based on VLAN+802.1p priority.

Category 2: mapping based on port ID, mapping based on port ID+VLAN, mapping based on port ID+802.1p priority, and mapping based on port ID+VLAN+802.1p priority

Category 3: mapping based on IP ToS

Category 4: mapping based on VLAN+IP ToS

The type of flow control

Indicates the type of the flow control.

[thunderlinkcom]

what about display dba-profile bound-info(distributing-mode)

display dba-profile bound-info(distributing-mode)

Function

This command is used to query the bound information of the specified dynamic bandwidth assignment (DBA) profile, including the PON port to which the ONT that binds DBA profile connects, and the ONT ID.

Format

display dba-profile bound-info { profile-id profile-id | profile-name profile-name }

Parameters

Parameter

Description

Value

profile-id profile-id

Queries the bound information about the DBA of the specified ID.

Numeral type. Range: 0-512.

profile-name profile-name

Queries the bound information about the DBA of the specified name.

Character string type, a string of 1-33 characters. The name of a DBA profile cannot start with a quotation mark (").

Modes

Privilege mode, diagnose mode,  HG8245A

Level

Operator level

Usage Guidelines

In the privilege mode or global config mode, run the diagnose command to enter the Diagnose mode.

The command is used to query the information about the ONT which binds DBA profile using tcont bind-profile command. The DBA profiles which have been bound cannot be modified or deleted. You must unbound them using undo tcont bind-profile command first.

Example

To query the bound information about DBA profile 3, do as follows:

huawei#display dba-profile bound-info                                     { profile-id<K>|profile-name<K> }:profile-id                             { profile-id<U><0,512> }:3                                                                                  Command:                                                                                display dba-profile bound-info profile-id 3                             ----------------------------------------------------------------               Bound by ONT             ----------------------------------------------------------------               F/S/P       ONT List ---------------------------------------------------------------- 0/ 1/0      0,2-5 0/ 1/0      0,3 0/ 2/0      0,1,2 0/ 2/0      2 ----------------------------------------------------------------

System Response

The system displays the queried result when the command runs successfully.

The following table describes the parameters in response to the command.

For more information about the error message that the system displays against a command entered with incorrect syntax,

Parameter

Description

Bound by ONT(such as   HG8245H )

Displays the information about the ONTs which bind DBA profile.

F/S/P

Indicates the shelf ID, slot ID, and port ID of PON port which the ONT connects to.

ONT List

Indicates the ONT lists which bind DBA profile.