#maxiim im608

[obdiishop]

How to repair BMWMini electric windows by Autel IM608

My BMW/MiniFRM module is not responding and now the power windows are not working. It’s not like earlier cars could use hand-operated switches. So I decided to read the EEPROM and rewrite the corrupted data. This article will show you How to repair BMWMini electric windows by Autel IM608.

Tools used: Autel MaxiIM IM608 FRM Info Chip: MC9S12XEQ384 Mask: 3M25J

Path On Autel IM608, go to Programmer>>Chip (EEPROM,MCU,ECU)>>Chip read & write>>Other>>BMW>>E – SERIES>FRM>XEQ384>RW

Step 1. Read D-FLASH, EEPROM, P-FLASH Check “Schematic diagram”.

Connect APA109, IM608, XP400Pro and FRM circuit board by diagrams.

Go to “Set” to check if we’ve got 5 voltage, and turn on read/write/earse validation.

Then try to “Read” D-FLASH.

Empty, that’s why it is done.

Read Partition. Also empty.

EEPROM is also empty.

So we just read and save P-FLASH as a backup.

Usually this part is intact.

Step 2. Write partition

Go to D-FLASH and select “Write partition”. (So we can get a new EEPROM to write data in.)

Set EEPROM as 16, which will give you four kilobytes of memory on EEPROM.

Set D-FLASH as 0.

Step 3. Write EEPROM back

Then I find an EEPROM file with the same part number (3456395) on Google.

Of course this EEPROM belongs to a a different car, VIN…but it allows FRM to boot.

Transfer the data file to IM608 Key Programmer.

Go to “EEE” (EEPROM), and select “Write”.

Load the EEPROM file we just found.

Write successfully.

Go back to read D-FLASH and EEPROM.

FLASH is also empty, but we have the data in EEPROM.

Step 4 . Check FRM on car

Restore FRM back, and see if it boots well.

Use an Autel Diagnostic Tool to check windows quickly.

The wrong chassis means our FRM has communications.

Before we have a DTC about FRM error.

Diagnosis>>Control unit>>Body>>FRM2 (Footwell Module 2)>>Read codes

Now our FRM comes back.

And then the rest work is to program the module the car because it comes from a different car.

Notice: IM608 doesn’t support BMW X1 FRM program.

Credits to LM Auto Repairs.

Hope this could help.

https://blog.obdii.shop/how-to-repair-bmwmini-electric-windows-by-autel-im608/

[qingqin]

Program Toyota Camry 2016 8A All Smart Keys Lost using Autel Simulator via OBD

How-to: program Toyota Camry all smart keys lost, generate simulator and add new smart key with Autel MaxiIM IM508and APB112 simulator.

Vehicle Model: Toyota Camry 2016 hybrid Key chip: 8A Lost all keys, new smart key cannot turn on key not detected and remote do not function

Device required:

Autel IM508/IM608

XP400 Adapter

Autel APB112 smart key simulator

A new smart key

Main Step: 1. Read IMMO data 2.Generate Simulator Key 3. Add Smart Key

Step-by-step procedure:

Connect APB112 with IM508 via USB cable Select IMMO->Toyota->Manual Selection->Other->Camry->Smart key->Keyless System (CAN)

1. Back up Immobilizer Data This function is use to back up the EEPROM data of the smart box. The data can be used to generate the simulator key for emergency start of the vehicle to perform the key programming function.

Reading immobilizer data

Connecting network. Need stable WiFi network Write name file and press OK to save dump

Backup succeed

2.Generate Simulator Key

Select Generate Simulator Key Select the EEPROM data Choose backup file

Retrieving critical data Generate simulator key in process

Show key type SLK03 Connect APB112 key simulator

Obtain software name and version

Burning firmware until succeed The simulator key is generated successfully The simulator key can be used to turn the ignition on in case of emergency to learn the key

Put the simulator key on Start/Stop button and press

The key can start engine now.

Don’t disconnect USB cable

3. Add smart key Use the simulator key to turn on ignition

Select Add Smart Key Confirm to use the simulator key APB112 Each step must be completed within the specified time. The position for learning: 5

Put the simulator key APB112 close to Start button

You will hear a beep sound Put the new smart key to learned close to the Start button

beep beep Registering key in process

Learning key succeed Test remote and star vehicle

Done.

Note: APB112 simulator need to work with Autel Scanner XP400 (not  XP200) and compatible with IM608, IM508, MX808IM. It is not only a smart key simulator, but also 46, 4D data collector and ID46 password calculator.