seen from Belgium
seen from Türkiye
seen from China
seen from Malaysia
seen from France
seen from Canada
seen from Canada
seen from Singapore
seen from France
seen from United States
seen from United States
seen from Australia
seen from China
seen from China
seen from Netherlands
seen from Türkiye
seen from China
seen from United States
seen from Germany
seen from France
Mastering SAE J1939: Real-Time Simulation & Monitoring Made Easy
Streamline your SAE J1939 application development with the Copperhill ECU Simulator and free JCOM1939 Monitor software. Test, simulate, and analyze J1939 data traffic with ease—ideal for engineers, developers, and vehicle network professionals.
Test, simulate, and analyze J1939 data traffic with ease—ideal for engineers, developers, and vehicle network professionals.
OS-Independent, License-Free On-Chip SAE J1939 Protocol Stack for Embedded, Linux, and Windows Systems
Copperhill Technologies offers a variety of hardware modules equipped with an On-Chip SAE J1939 Protocol Stack, relieving the end user from implementing third-party source code and avoiding license fees. The programming of J1939 network communication is accomplished through accessing a standard serial port, making the development virtually independent of the operating system.
https://www.prlog.org/12865516
Arduino-Compatible Programmable CAN FD to USB Gateway
This board uses the Teensy 4.0 as a CAN FD to USB converter. The Teensy 4.0 comes with a high-speed 480Mbit/s USB HS interface. The MCP2558FD CAN FD transceiver is rated up to 8Mbps with silent mode under control via software or hardware link.
The MCP2557/8FD is a Microchip Technology Inc. high-speed CAN transceiver/CAN Flexible Data Rate Transceiver with Silent Mode. The devices meet and exceed CAN FD specification requirements in addition to the latest Automotive OEM requirements.
The Teensy 4.0 features an ARM Cortex-M7 processor at 600 MHz, with a NXP iMXRT1062 chip. It can be programmed using the Arduino IDE with Teensyduino add-on.
https://copperhilltech.com/teensy-4-0-can-fd-to-usb-converter/
Teensy 4.0 CAN FD Gateway with high-speed 480Mbit/s USB HS interface
This board uses the Teensy 4.0 as a CAN FD to USB converter. The Teensy 4.0 comes with a high-speed 480Mbit/s USB HS interface. The MCP2558FD CAN FD transceiver is rated up to 8Mbps with silent mode under control via software or hardware link.
https://copperhilltech.com/teensy-4-0-can-fd-to-usb-converter/
SAE J1939 Processor Module With USB Port, RTC, MicroSD Memory Card
The jCOM.J1939.USB processor board is a high-performance, low-latency vehicle network adapter for SAE J1939 applications. It allows any host device with a USB COM port to monitor SAE J1939 data traffic and communicate with the SAE J1939 vehicle network.
The board supports the full SAE J1939 protocol according to J1939/81 Network Management (Address Claiming) and J1939/21 Transport Protocol (TP). It is also supported by an extensive programming interface for Windows and Linux/Ubuntu applications, including full C/C++/C# source code for short time-to-market developments.
The JCOM.J939.USB-X SAE J1939 Processor board is an extended version of our popular JCOM.J9139.USB-B SAE J1939 ECU Simulator Board With USB Port.
The improved features are:
Upgraded ARM Cortex-M3 processor with double Flash & RAM
Supports Hi-Speed USB 2.0 transfer rate at up to 480 Mbps
Additional UART-USB for onsite firmware programming
Onboard Real-Time Clock (RTC) for CAN Bus message timestamp support
MicroSD Memory Card support
4-position DIP switch (one for termination resistor, three for functionality settings)
Additional serial (UART) port for GPS sensor or SAE J1708 board
https://copperhilltech.com/sae-j1939-processor-module-with-usb-port-rtc-microsd-memory-card/
Arduino-Due-Based USB Gateway With Two CAN Bus Ports
The jCOM.DUE.CORE-B board combines two of our products into one:
Dual CAN Bus Interface for Arduino Due
Due Core - Arduino Compatible SAM3X8E 32bit ARM Cortex M3 Module
The CAN Bus board incorporates dual CAN transceivers required by the two integrated CAN ports on the Arduino Due, i.e. they convert the CAN TTL signal into a differential voltage as required by the CAN Bus Standard (ISO 11898).
The Due Core is a microcontroller board based on Arduino Due, featuring the Atmel SAM3X8E ARM Cortex-M3 CPU.e
https://copperhilltech.com/arduino-due-based-usb-gateway-with-two-can-bus-ports/
USB Module with 2 CAN FD Interfaces Plus Analog And Digital IRIG-B Inputs
The CAN-USB/400-FD by esd electronics is equipped with two independent CAN FD interfaces according to ISO 11898-1:2015; they are driven by the ISO 16845:2004 certified esdACC (esd advanced CAN Core) implemented in an Altera® FPGA. The interface is able to send and receive ISO conform CAN FD (up to 5 Mbit) or CAN 2.0 A/B messages. The CAN FD bit rate range is validated for the esdACC CAN FD core from 10 kbit/s up to 5 Mbit/s.
http://copperhilltech.com/blog/usb-module-with-2-can-fd-interfaces-plus-analog-and-digital-irigb-inputs/
