Untitled

[simrahali-blog1]

FINAL PROJECT

My Final project was a Dispenser, My concept Behind this project was to have  my own Dispenser because it will be useful for me in get togethers at my place. my guests can refresh their drink by themselves and it’s convenient for me as-well. As a host i do not have to worry about serving drinks to them. 

Attached is the picture of my final work which is separated in 3 parts.

First picture is i made out enclosure from card board to see how it will look.

Second picture is the wood being laser cut in laser cutting machine.

Third picture is the final enclosure of my dispenser.

Supplies:

Industrial Glue, Batteries, Plastic Tubes, Wires, Air pump, Buttons.

I put it all together with industrial glue.

PROCEDURE:

It works with air pump, buttons, batteries & Tubes, i used two bottles, coke & sprite, for each bottle i used separate batteries. i solder the wires, buttons & air-pump together. lastly i  attached plastic tubes with air-pump and put it in bottle & lastly i made sure that bottle cap were sealed so air won’t come out and as you can see in picture attached, coke is dispensing in cup. 

[simrahali-blog1]

Final Project Ideas: My final project idea is to make FOUNTAIN MACHINE

Concept: I want to to built this, because when you have get together in your home, It’s annoying to serve people drinks, so the idea is that my guests can refresh their drink by themselves and it’s convenient for me aswell. As a host i do not have to worry about serving drinks to them. 

Attached is the picture of the wireframe of my Project.

Materials that i will need is Plexi glass, i will be making my fountain machine from a Plexi glass, other components i need is Push buttons, Air pump, Led’s, tube, some wires & Soda bottles. 

[simrahali-blog1]

MIDTERM PROJECT

My project was a Piggy Bank, My concept Behind this project was to make my own personal piggy bank where i can save money, It was interesting to me so i thought it would interest to use it aswell and at the same time it would help me too.

Attached is the picture of my setup of arduino.

How it works:

It works with ultra sonic sensor as you can see in picture above, which is also called distance sensor, with sensor you put your hand in-front and it opens the piggy bank with the help of servo motor to put the money in piggy bank. 

Code:

#include <Servo.h>   //servo library Servo servo;     int trigPin = 5;     int echoPin = 6;   int servoPin = 7; int led= 10; long duration, dist, average;   long aver[3];   //array for average void setup() {          Serial.begin(9600);    servo.attach(servoPin);      pinMode(trigPin, OUTPUT);      pinMode(echoPin, INPUT);      servo.write(0);         //close cap on power on    delay(100);    servo.detach(); } void measure() {   digitalWrite(10,HIGH); digitalWrite(trigPin, LOW); delayMicroseconds(5); digitalWrite(trigPin, HIGH); delayMicroseconds(15); digitalWrite(trigPin, LOW); pinMode(echoPin, INPUT); duration = pulseIn(echoPin, HIGH); dist = (duration/2) / 29.1;    //obtain distance } void loop() {  for (int i=0;i<=2;i++) {   //average distance    measure();                 aver[i]=dist;                delay(10);              //delay between measurements  } dist=(aver[0]+aver[1]+aver[2])/3;     if ( dist<50 ) { //Change distance as per your need servo.attach(servoPin);  delay(1); servo.write(0);   delay(3000);       servo.write(150);     delay(1000); servo.detach();       } Serial.print(dist); }

[simrahali-blog1]

FADE LIGHTS

[simrahali-blog1]

FADE LIGHTS

[simrahali-blog1]

[simrahali-blog1]

SALT SWITCH