#101project

[chichunchen]

Conductive wool and thread

This week we tried out different conductive materials.

I was exploring with conductive wool and thread.

I embed the LED into wool and connected them with conductive thread. 

The conductive wool itself turned into as a resistor which offer a changeable value to the arduino.

This is a demo that I triggered the sound with this custom sensor.

    Project / One - O - One

Date / 12-14. 05. 2014

Site / Weissensee Kunsthochschule Berlin

Project leader / Prof. Mika Satomi

[chichunchen]

BLume - process#02

SMA Test

The SMA I use : Flexinol Wire 0.010" LT / data sheet

The main point of the test have been aim at the whole configuration of my lighting unit design:

- the balanced movement of four corners

- control the tilt angle and distance between the surface panel and the mechanism base

- regulate the length of the SMA and the angle that fit in between top surface and the base

- stabilise and place the SMA ( enhance the strength make it able to stand)

- try out a way to embed the SMA with the material

- find out the right material which could active by the SMA perfectly and provide a better performance

- calculate  the length of the SMA and the max. voltage and the right current

  Structure One

First I tried with this structure which is able to active the corner and create the bendy / folding motion.

Materials:

- SMA / I60mm *2 

- pvc tube / Ø2mm

- foam / 150 * 150 *3mm

- wooden base / as the above diagram

Method:

- use the pvc tubes to hold and fix the SMA

- test with two diagonal corners

Problems:

- the motion is limited in bendy corner ( not bad)

- without any external support the top surface panel is not balanced when moving

- the SMA need space to move / now fix with the plc tubes which is too easy melted by the heat of the SMA

- the foam is a bit too thick

Structure Two

After the Structure One, I tried to solve the problems before and build a new structure which include a central support. Also I narrowed down the size of the base that provide more space for the movement.

Materials:

- SMA / 220mm *2 

- pvc tube / Ø2mm

- foam / 150 * 150 *3mm

- wooden base / as the above diagram

- universal joint

- soft sides support

Method:

- Universal joint to balance the panel when moving

- longer distance between surface and the base

- build the supports for fixing the SMA / made out by foam

Improvement:

- the motion is more stable

- central support increase the strength of the whole structure

- increase the movement 

Problems:

- still need to find out a better way to fix and support the SMA

- to think about what kind of motion is better/ bendy corner or average tilt

[chichunchen]

Tilt Switch

Tilt Switch actually just work as a simple switch to make open and closed circuit.

Open a tilt switch, we can see there are to conductive balls inside a copper tube. There are two pins with this switch, one connected to the outer copper tube, and another one go into the tube and which would connect with the rolling ball in there.

The circuit closed when the balls are conducted with the copper tube and inner pin. Conversely the circuit open when turning the switch upside down that avoid the small ball to touch the pin.

But why there are two balls? One is bigger and another is smaller. I think the bigger ball actually has two function. First it helps to conduc with the copper tube; second, it is heavier that would provide the weight to help the smaller ball stably conduct with the pin.

    Project / One - O - One

Date / 19-21. 05. 2014

Site / Weissensee Kunsthochschule Berlin

Project leader / Prof. Mika Satomi, Hannah Perner-Wilson

[chichunchen]

DIY Magnetic Motor

Lets see how it works.

There are still couple problems I haven't figured out. The motor I have done now still couldn't turn very well, somehow it could be the problem of the structure design or the number of laps of the spiral is not enough.....   So the next step would be redesign the whole construction. The copper thread seems like not strong enough.. after turning for a while it broke. So which tells us there are also some problems of soldering and material...   Ooops !  

Project / One - O - One

Date / 19-21. 05. 2014

Site / Weissensee Kunsthochschule Berlin

Project leader / Prof. Mika Satomi, Hannah Perner-Wilson

[chichunchen]

BLume - process#01

Form test and paper prototype

Problems:

- it's difficult to direct the light source only by changing the form

- single light resource and the position seems blur the concept of light leaking 

- the folding structure will make the SMA difficult to move (too tight)

- how the amount of the movement influences the brightness and the effect of visual performance for the presentation

Design principles for light control:

- external cover for light and inside mechanism

- soft light weight material and smoothy joint provide better condition to active the SMA

- control light leak by material : cut a gap on closed surface, translucent material at the side, four leds for each corner + one led at the central + controlled by program...

- build a black box for the presentation to show better lighting effect 

Polyhedron Form

After testing the lighting effect, I tried to think about different possibilities of the movable surfaces. I make some polyhedron cylinders with different proportion. By cutting out specific gaps on the certain surfaces that helps me to enhance the flexibility and create movable structure.

  Problems:

- the structure would be too complicated to active the SMA / motion of stretch and squeeze which definitely need to train the SMA which I don't think I have enough time to reach the perfect parameter I need

- the motion couldn't fit the function of regulating the light direction

- too functionally and visually complicated...

  Discovery:

The polygon texture on the surface create the fascinating visual effect, which  brings more perception of dynamic surface. Also the texture create the shadow so visually enhance the movement of the SMA itself.

Design Principles:

- keep the structure and motion as simple as possible that would be better for applying the SMA into the object

- use polygon 3d texture on the moving surface

- to regulate the light direction, keep the base structure developing in the square box which could be fixed on the wall rather than grow the object into cylinder way..... 

[chichunchen]

Blume - concept

Breathing Light - Modular Lighting Unit

    Motivation

  Thinking about the responsive surface of the object and its function, base on my own perspective I think the function should work more directly connected with the surface materials.

  Recall the concept of “Kit of the no parts” that point out why all Consumer Electronics should be covered with a "shell". However, I call this “Shell” surface. The surface of a product that made out of any materials in reason and contains the semantic. The semantic instructs the users that how to use the product, also to protect and maintain the function of the inside mechanism and also prevent users hurt from electricity.

  Nowadays with new material technology, such as e-textile, smart material that are interactive and responsive which provide the users unexpected and changeable feedback. Furthermore we expect to integrate the interaction into our daily behaviour and immerse our motion into the object. But the exist application so far seems still restricted in the limited scale. Therefore I attempt to rethink the communication between the users and the objects, and the relationship between the materials, surfaces and the usabilities.

    Idea

  I attempt to embed the SMA into a soft membrane panel or tactile material and to create a behaviour with the motion of lifting something up and getting bright.

Simple square geometry with four bendable corners, the users can puzzle these panels into any shape which would also reach the users' needs.  So the user can decide the bright point to control the lighting direction for different situations.

This system is flexible and functional. Users can mix the functional panels and solid panels to create the patterns and breathing surface.

  I would also design an interface to operate. I am thinking to make a switch with spot pot or tactile button, the operator interface will design into relative shape with the lighting panel which is intuitive finger gesture match the panel's motion and moving direction. Or also could use the photocell to directly induce the approaching hands right at the expected bright point. But still have to test the circuit to control the SMA first and decide which way is better.  

///  under process  ///

[chichunchen]

Luminous Textile

Light could be flexible and haptic.  Integrate electronic into soft materials to bring a new configuration of the object and new perception for users.

This week we used the table loom to weave and try to embed lighting unit into the textile in a simple way.

I took a EL-wire and woven it with thread which produce an illumine fabric.

After producing my own material, I apply it into a lamp design. Because of the material which is light weight, soft, flexible so make this lamp durable and portable. 

The users could twist the fabric to create the shape of the lamp. Combine with the different shape of support and base of the lamp, the material would follow and fix the shape. Its a deformable contour of the objects.

Project / One - O - One

Date / 28-30. 05. 2014

Site / Weissensee Kunsthochschule Berlin

Project leader / Prof. Mika Satomi

[chichunchen]

Arduino and Sensor 2

Following the last post, we had the concept about the difference between digital and analog sensor. Now here we have more trails for different resistive analog sensors and output device. 

Trails 

1) SoftPot Round / Straight

2) Flex / Bend sensor

3) Application - mini speaker  

.....................................................................................................

SoftPot Round / Straight

The Softpot sensors actually work as the potentiometer. Instead of turning a knob, you can touch it.  The Softpot sensors change their resistance depending on where your finger is touching.

Plug in the middle pin to an analog in pin on the arduino, and the analogRead the value between 0 to 1023 depending where you touch it. For example, on the Softpot-straight, it will be read about 512 when touched in the middle.

Task /

Try to create a gradually brighter LED light that controlled by Softpot sensors.

    Flex / Bend sensor

Flex sensor, resistive sensor also works as the potentiometer. It is a flexible strip that changes its resistance when bent. The bigger curvature creates the bigger resistance.

How it works?

One side of the sensor is printed with a polymer ink that has conductive particles embedded in it. When the sensor is straight, the particles give the ink a resistance of about 30k Ohms. When the sensor is bent away from the ink, the conductive particles move further apart, increasing this resistance. When the sensor straightens out again, the resistance returns to the original value. By measuring the resistance, you can determine how much the sensor is being bent.

The circuit here include an extra resistor which makes a voltage divider to make the reading possible.

Task /

Create a gradually brighter LED light that controlled by Flex sensor

  Application - mini speaker

We can connect these resistive sensors with mini speaker and use Arduino tone library to play some music !

Task /

Control the pitch by potentiometer 

  Control the pitch by Flex sensor

    Project / One - O - One

Date / 05 05. 2014

Site / Weissensee Kunsthochschule Berlin

Project leader / Prof. Mika Satomi