seen from China
seen from United States
seen from Malaysia
seen from United States
seen from United States
seen from United States
seen from Türkiye
seen from United States
seen from United States
seen from Canada
seen from China
seen from China
seen from Austria
seen from United States
seen from Malaysia
seen from Malaysia
seen from United States
seen from Malaysia
seen from United States
seen from Germany
Good News for all visitors of amplifiercircuit.info. From today this portal will present best prices for amplifier kits from worldwide. Buy Top 20 Amplifier kits.
These products have a good review and and no doubt stand, because they will meet your requirements you.
200W Subwoofer Amplifier Circuit
Circuit Description Here is a circuit that uses a...
TDA7294 Audio Amplifier 2 x 80W
TDA7294 general description: This circuit described...
TDA2030 Audio Amplifier 1 x40W
TDA2030 g eneral description: Although there...
LM3886 Audio Amplifier 1 x 108W
LM3886 g eneral description: According to...
1000W Audio Power Amplifier for Subwoofers
Description The IRS20124 is a high voltage, high...
What’s more, unpredictable feedback may cause damage to the speakers and is very unpleasant on the ear. This cheap little easy-to-build project can help solve these technical problems.
How many amateur music groups sing through an amp borrowed from a guitarist or bass player? These days, music is a major hobby for the young and not-so-young. Lots of people enjoy making music, and more and more dream of showing off their talents on stage. But one of the major problems often encountered is the cost of musical equipment. A guitar (or bass guitar) amplifier is designed first and foremost to reproduce the sound of the guitar or bass as faithfully as possible. This is where the technical problems arise not in terms of the .25” (6.3 mm) jack, but in terms of the sound quality (the words are barely understandable) and volume (the amp seems to produce fewer decibels than for a guitar). That’s just what this circuit attempts to do. The frequency response of the amp doesn’t need to be as wide or as flat as in hi-fi (particularly at the high end), and so this sort of amplifier won’t permit faithful reproduction of the voice. If you build an adaptor to compensate for the amp’s limited frequency response by amplifying in advance the frequencies that are then attenuated by the amp, it’s possible to improve the quality of the vocal sound.
Guitar vocal adaptor amp
Bass guitar super bridge amplifier 200 watt. If you want to circuits amplifiers for bass guitar, or for using in every situation such as both listen to in the house, outside the house or outdoors. this. Guitar amp tone effects placement, Information about distortion voicing, effects placement, and cranked-tube-amp tone at any volume.. Amp parts | guitar center, Enjoy the lowest prices and best selection of amp parts at guitar center. most orders are eligible for free shipping!
Guitar amplifiers are always an interesting challenge. The tone controls, gain and overload characteristics are very individual, and the ideal combination varies from one guitarist to the next, and from one guitar to the next. There is no amp that satisfies everyone's requirements, and this offering is not expected to be an exception. The preamp is now at Revision-A, and although the complete schematic of the new version is not shown below, the fundamental characteristics are not changed - it still has the same tone control "stack" and other controls, but now has a second opamp to reduce output impedance and improve gain characteristics.
One major difference from any "store bought" amplifier is that if you build it yourself, you can modify things to suit your own needs. The ability to experiment is the key to this circuit, which is although presented in complete form, there is every expectation that builders will make modifications to suit themselves. The amp is rated at 100W into a 4 Ohms load, as this is typical of a "combo" type amp with two 8 Ohm speakers in parallel. Alternatively, you can run the amp into a "quad" box (4 x 8 Ohm speakers in series parallel - see Figure 5 in Project 27b, the original article) and will get about 60 Watts. For the really adventurous, 2 quad boxes and the amp head will provide 100W, but will be much louder than the twin. This is a common combination for guitarists, but it does make it hard for the sound guy to bring everything else up to the same level. more info on here
This is a medium power guitar amplifier is recommended especially for portable amplifier. The amplifier is a combination between a simple integrated audio driver, LM391-80 and a stage of output power designed contratemps with bipolar transistors.
Thermistor NTC, which is in temperature contact with output power transistors, allows to separate AO LM391 power stage when it heats too much.
The start of the thermal protection is at a NTC flow current NTC of approximately 200uA. Electrolytic condenser asure a “smooth start” to remove clicks that may occur when connecting the amplifier. It can happen that the protection can be too sensitive, in that case certain adjustments are admitted in the value of R4 or thermistor.
The standby current can be adjusted with P1. This potentiometer is initially 0 and then is adjusted to achieve a current of 50mA. Current can be increased up to 400mA if you want low distortions.
The power transistors are placed on the same side of printed circuit board, so that it can be mounted on a heatsink jointly with the thermistor. The heatsink must be large enough and have the thermal resistance of maximum 10K / W.
L1 has 20 turns with 0.8mm emailed copper, coiled over R21. C9 is a ceramic capacitor.
Guitar Amplifier Circuit
Guitar Amplifier Circuit
A preamplifier circuit suitable for high impedance type electric guitar pickups is given here.The circuit is based on a uA 741 op-amp (IC1).The IC1 is wired as a non-inverting amplifier.The POT R1 can be used as a volume controller.The POT R6 can be used as tone controller.The switch S1 is used to produce “brilliant” or “soft” tonal effects.
Assemble the circuit on a good quality PCB or common board.
The amplifier can be powered from a 12V battery or 12V DC power supply.
Up to 24 V DC can be used to power the circuit.i recommend 12 V DC.
The IC 1 should be mounted on an IC base
Circuit Diagram:
Guitar pre-amplifier
This small amplifier was intended to be used in conjunction with an electric guitar to do some low power monitoring, mainly for practice, either via an incorporated small loudspeaker or headphones.
The complete circuit, loudspeaker, batteries, input and output jacks can be encased in a small box having the dimensions of a packet of cigarettes, or it could be fitted also into a real packet of cigarettes like some ready-made units available on the market.
This design can be used in three different ways:
Mini Portable Guitar Amplifier
Max output power: 1.5W @ 9V supply - 8 Ohm load; 60mW @ 3V supply - 8 Ohm load
Frequency response: Flat from 20Hz to 20kHz
Total harmonic distortion @ 100mW output: 0.2%
Max input voltage @ 3V supply: 8mV RMS
Minimum input voltage for Fuzz-box operation: 18mV RMS @ 3V supply
Current consumption @ 400mW and 9V supply: 200mA
Current consumption @ 250mW and 9V supply: 150mA
Current consumption @ 60mW and 3V supply: 80mA
Quiescent current consumption: 6mA @ 9V, 4mA @ 3V supply
Fuzz-box current consumption: 3mA @ 3V supply
