seen from Australia
seen from China
seen from United States
seen from France
seen from Malaysia
seen from China
seen from Switzerland
seen from Maldives
seen from South Korea
seen from Brazil
seen from Germany
seen from Russia
seen from Argentina
seen from United Kingdom
seen from United Kingdom
seen from Italy
seen from Italy
seen from Argentina
seen from Türkiye
seen from Italy
BLK FRIDAY ACTIVE 11/18 - 11/25 🌑 15% OFF EVERYTHING CODE DISCO22 AT CHECKOUT. @rude.scott Old #E30 #S52 #OBD1 w all #E30M3 uprights circa 2013 that started #Renown. www.renownusa.com (at Renownusa.com San Francisco) https://www.instagram.com/p/ClJnzSHp0Bw/?igshid=NGJjMDIxMWI=
Honda OBD1 16 Pins DIY Diagnostic Without OBD Scanner
Honda OBD1 16 Pins DIY Diagnostic Without OBD Scanner
HOW TO READ OBD1 CODES ON HONDA 16 PIN DLC How to read codes
LEASE NOTE:If after following the instructions below the Check Engine Light does not flash it either means there are no fault codes or there is a connection error. To test connection, remove the TPS and run the engine then recheck codes.
If possible run the engine to bring the oxygen sensor up to operating temperature then switch the…
View On WordPress
Daihatsu OBD1 17 Pin DIY Diagnostic without OBD Scanner
Daihatsu OBD1 17 Pin DIY Diagnostic without OBD Scanner
HOW TO DIAGNOSE DAIHATSU OBD1 17 PIN WITHOUT OBD TOOLS Accessing Code
Trouble codes are displayed by the malfunction indicator lamp (MIL).Fig5
Switch ignition ON.
Bridge data link connector (DLC) terminals 1 and 2 Fig. 1 .
If no trouble codes are stored, the lamp will flash twice per second Fig. 2 .
Each trouble code consists of two groups of one or more flashes Fig. 3 [A].
MIL flash duration:…
View On WordPress
Daihatsu OBD1 16 Pin DIY Diagnostic Tutorial
Daihatsu OBD1 16 Pin DIY Diagnostic Tutorial
HOW TO DIAGNOSE DAIHATSU OBD1 16 PIN WITHOUT OBD SCANNER Accessing Code
Trouble codes are displayed by the malfunction indicator lamp (MIL).Fig.5
Switch ignition ON.
Bridge data link connector (DLC) terminals 4 and 6 Fig. 1 .
If no trouble codes are stored, the MIL will flash twice per second Fig. 2 .
Each trouble code consists of two groups of one or more flashes Fig. 3 [A].
Warning lamp flash…
View On WordPress
How to Diagnose Suzuki OBD1 Year 1991-1999 Without OBD Scanner
How to Diagnose Suzuki OBD1 Year 1991-1999 Without OBD Scanner
HOW TO DIAGNOSE ISUZU OBD1 WITHOUT OBD SCANNER FROM YEAR 1991-1999
Preparatory conditions
Ensure battery voltage above 11 volts. Transmission in neutral. All auxiliary equipment, including air conditioning, switched OFF.
Method 1 – except Germany
Trouble codes are displayed by the malfunction indicator lamp (MIL).FIG3
Switch ignition ON.
Check that MIL illuminates.
Install a spare fuseto…
View On WordPress
HOW to Read Suzuki OBD1 Codes 5 Pin without OBD Scanner
HOW to Read Suzuki OBD1 Codes 5 Pin without OBD Scanner
HOW TO READ SUZUKI OBD1 CODES (5 PIND DLC) WITHOUT OBD SCANNER
Preparatory conditions
Ensure battery voltage above 11 volts.
Transmission in neutral.
All auxiliary equipment, including air conditioning, switched OFF.
Accessing trouble codes
Trouble codes are displayed by the malfunction indicator lamp (MIL).
Switch ignition ON.
Check that MIL illuminates.
Bridge data link connector (DLC)…
View On WordPress
HOW TO Diagnostic Suzuki OBD1 6 Pin without OBD Scanner
HOW TO Diagnostic Suzuki OBD1 6 Pin without OBD Scanner
HOW TO DIAGNOSE SUZUKI 6 PINS OBD1
Accessing Code
Trouble codes are displayed by the malfunction indicator lamp (MIL).
Switch ignition ON.
Check that MIL illuminates.
Bridge data link connector (DLC) terminals 1 and 2 Fig. 1 .
Count MIL flashes. Note trouble codes. Compare with trouble code table.
If MIL remains illuminated: Suspect faulty engine control module (ECM).
Each trouble code…
View On WordPress
Toyota Startlet 1996-1999 Obd1-Diy Diagnostic Tutorial
Toyota Startlet 1996-1999 Obd1-Diy Diagnostic Tutorial
General information Trouble codes are displayed by the malfunction indicator lamp (MIL). Late models: The ECM fault memory can also be checked using diagnostic equipment connected to the data link connector (DLC).
Accessing
Normal mode 1 Switch ignition ON. 2 Bridge data link connector (DLC) terminals E1 and TE1. SOHC: Fig. 1 . DOHC: Fig. 2…
View On WordPress
