#waterproof services

[xincwaterproof]

XINC Waterproof Diary: How to Operate the Waterproofing of Building External Walls

1.The waterproofing and anti cracking measures for the exterior wall should be set up based on factors such as the construction and materials used, the height of the exterior wall, basic wind pressure, and the decorative layer of the wall.

2. Concrete exterior walls should not use sleeve type pull screws, but tool type pull screws. Both ends of the wall should have reinforced sealing measures at nodes.

3. Before applying the leveling layer to the exterior wall, a layer of polymer cement interface treatment agent should be applied as the base bonding layer.

4. Hot dip galvanized steel mesh should be installed inside the external wall leveling layer as crack resistance measures, and should be installed at the 1/2 to 1/3 section of the mortar.

5. The masonry mortar at the junction of wall beams and wall columns must be full, and steel mesh should be hung for crack resistance measures. It is suitable to pour polymer cement slurry into this area to strengthen sealing and embedding.

6. The walls within 200mm around the exterior wall doors and window openings should be filled with fine aggregate concrete, and the interior and periphery of the door and window openings should be coated with 5-thick polymer cement waterproof mortar as a waterproof reinforcement layer.

7. The joint between the window frame and the wall should be filled with polymer cement mortar. If the joint is larger than 30mm, it should be filled in two stages; If the frame joint is greater than 50mm, polymer fine aggregate concrete needs to be filled.

8. The deformation joint of the external wall must be treated with waterproofing and sealed with synthetic polymer waterproofing membrane.

[xincwaterproof]

XINC Waterproof Decoration Strategy: Answers to Common Waterproof Questions

With the increase of the service life of existing buildings and the quality problems of the building itself, quality problems such as waterproof leakage and wall damage occur frequently. What we will bring to you are common causes of leakage and solutions.

Problem 1: The waterproof layer is not firmly adhered and is easy to lift

Reason: After removing the bulging waterproof layer, it was found that there were a large amount of floating dust and debris adhering to the back of the waterproof layer. The main reason is that the base layer of the wall has sand, is not solid, loose, or a large amount of floating soil, floating ash, etc., which leads to unstable bonding between the waterproof layer and the base layer. During the closed water test, the water pressure caused the coating to contract again.

XINC Waterproof Method: In response to the problem of sanding and instability of the on-site base layer, it is recommended to first use a reinforcing agent to cover the base layer, enhance the adhesion of the wall base layer, and then carry out the application of waterproof paint.

Problem 2: Needle holes and bubbles appear in the waterproof coating film

Reason: The base layer is too dry or has a large porosity. After applying this type of base layer, the base layer will absorb the moisture in the coating, which occupies the voids originally occupied by air. The air in the pores will be discharged, forming pores on the surface of the waterproof coating.

XINC Waterproof Method: Before construction, wet the base layer with water (without open water) or treat it with reinforcing agent and water adhesive. Apply multiple times during the first coat, and the second coat can completely cover it.

Problem 3: Local cracking of waterproof coating

Reason: The coating is too thick in one application; The base layer is uneven, and the paint flows towards low areas; During the drying process of the coating, the local curing of the coating is uneven; Before the coating film solidifies, proceed with the second coat: the first roll coating is thicker and not completely dry, so proceed with the second roll coating. This results in different drying rates for the two layers of coating film, faster evaporation of surface moisture, and slower evaporation of the inner layer of coating moisture, resulting in different internal and external shrinkage stresses, resulting in shrinkage differences, and the formation of surface cracks.

XINC Waterproof Method: Apply additional coating to the cracked area; Or remove the paint from the cracked area, level it with cement mortar, apply arc treatment to the internal corners, and carry out waterproofing construction again.

Problem 4: The waterproof film turns white after drying

Reason: Adding too much water or having clear water on the base layer causes the slurry to be very thin, causing the liquid to float and aggregate, leading to whitening; The unevenness of the base course and the accumulation of materials at the potholes lead to partial incomplete solidification of lotion; There is a lot of exposed water at the grassroots level, and the water dilutes the waterproof coating; When the humidity is high and the indoor temperature is low, the moisture in the air can easily form condensation (condensation) on the walls and floors.

XINC Waterproof Method: Strictly control the amount of water added and stir thoroughly; Before painting, the base layer should be ensured to be flat and free of open water; Strengthen ventilation and accelerate air circulation speed.

[xincwaterproof]

XINC Waterproof Diary: Problems that cannot be ignored in waterproof construction

The first few questions that waterproof construction work needs to understand are very important for your project!

1: Indoor waterproofing should ensure that the base layer is firm and does not shed bricks.

The most common aspect of indoor waterproofing is the treatment of toilets and bathrooms. If the strength of the base layer is low, the waterproof layer and the structural base layer will not bond firmly. Under the external force of the subsequent protective layer and decorative layer, it will cause hollowing, detachment, and other phenomena, leading to a series of leakage disputes.

So, when checking the firmness, you can feel the surface of the base layer with your hands and observe if there is any cement or gravel falling off. If there are problems, they should be leveled and repaired in a timely manner.

2: Dust particles have a deep impact, and quality problems arise from this.Previously, it was always said that the base layer should be kept clean before waterproofing treatment can be carried out. Why must we be so cautious? Because the presence of dust will act as a barrier between the base layer and the waterproof layer.

Especially organic waterproof coatings, which have a high surface tension during construction, are not easy to soak and spread In dust, if the coating cannot fully bond with the solid base layer, there is a risk of the waterproof coating film falling off.

3: Water vapor must not be left behind to prevent bubbles from filling the walls.

Here we will talk about another important issue, which is the moisture content of the base layer. The presence of grassroots moisture poses a significant threat to the organic waterproof layer. Because organic waterproof coatings are not only impermeable, but also airtight, once the moisture content of the base layer is too high, the waterproof coating will be blown and bulged by water vapor pressure, resulting in bubble problems and affecting the waterproof effect.

[xincwaterproof]

XINC Waterproof Decoration Suggestion: How to Targetedly Repair Roof Leakage Problems?

When there is a roof leak, the first step is to determine the leak point, conduct investigation and analysis, and then carry out targeted repairs. If the roof leakage is caused by incomplete bonding or damage to the waterproof layer, it is important to first identify the leakage point and then repair it with the same waterproof material.

If the leakage is severe, further waterproofing treatment is needed. When inspecting weak areas such as roof downspouts, gutters, and downspouts, if damage is found to the waterproof layer, special waterproof materials such as general waterproof glue can be used for reinforcement and waterproofing treatment. When cracks are found on the roof leading to water leakage, the cracks should be enlarged first, cleaned with a cutting machine, and then filled with waterproof mortar or other special materials. If the leakage is caused by empty barrels, peeling, wrinkling, or other reasons, the damaged area needs to be enlarged to within 10 centimeters of the surrounding area and cleaned with a cutting machine. Then use a universal waterproof adhesive brush to repair, brush twice or more, and finally use the same waterproof material for large-scale waterproofing reinforcement. If the treatment of the internal and external corners is not perfect, causing water leakage in weak areas, the first step is to find the leakage point, conduct investigation and analysis, and determine the repair method.

If it’s just a small leak, it can be sealed with universal waterproof adhesive produced by XINC waterproof. If there is extensive damage that causes water seepage, a new waterproof layer needs to be made. Before waterproofing, the edges and corners should be rounded, chamfered, layered, and finally subjected to large-scale waterproofing treatment. If it is treated with general waterproof adhesive, it needs to be reinforced with internally reinforced fiberglass cloth before painting. When the sealing material ages and the bonding strength is insufficient, resulting in water seepage, the original sealing material must be cleaned before sealing and waterproofing. If the leakage is caused by the problem of the waterproof material itself, such as material warping, wrinkling, insufficient bonding strength, etc., the universal waterproof adhesive should be replaced and waterproof treatment should be carried out again.

When the roof leaks, it is important to first identify the cause of the leak and then make targeted repairs. It should be noted that roof leakage not only affects the rooftop owners, but other owners also need to take it seriously. The issue of roof leakage is related to the vital interests of the entire building owner. If not dealt with in a timely manner, water seepage will flow down the cracks in the wall and then seep into the homes of residents on the first floor. If not resolved, it will not only affect the structural safety of the house, but also shorten the service life of the entire house. The maintenance cost that the owner ultimately needs to pay may far exceed that of a simple waterproof repair program.

[xincwaterproof]

XINC Waterproofing: Four Issues Concerning Waterproofing

Is the probability of water leakage in the bathroom high?

The bathroom area is very small, but the probability of water leakage is still as high as about one-third. Some may leak downstairs, while others may cause moldy walls and swollen floors due to horizontal leakage. With such a small area of the bathroom, the level of waterproofing is definitely much more meticulous and difficult than a large area of the roof. Moreover, after conducting a closed water test, there is no problem before tiling, and even so, the probability of water leakage is so high, The roof is equivalent to the area of several bathrooms, and the probability of water leakage is naturally not low.

Why did the closed water test leak when it was done well?

The closed water test tests the construction quality. Leakage represents poor construction, while waterproofing is a long-term dynamic process, just like a person who has not been sick before does not mean they will not be sick in the future. A material can be sold as a waterproof material, and conducting a closed water test is definitely not a problem. If it cannot pass even the closed water test, it cannot be sold as a waterproof material. Just like many waterproof materials that undergo various fancy experiments, it gives people the feeling that this material is really good. In fact, it’s just like the trick of selling powerful pills, deceiving consumers to pay for it. After all, consumers are all amateurs and can only see the appearance but not the essence.

I didn’t see any cracks, why did it leak?

Water is impenetrable, but only if the cracks are large enough can they be detected by the naked eye. However, as long as there is moisture or water leakage, it means there must be cracks here, and they are still penetrating cracks. Here is a little knowledge for science popularization. Cement and concrete are inherently waterproof materials, but they are rigid materials that will inevitably produce cracks under stress, thermal expansion and contraction, and time. Once the cracks penetrate, they will leak when encountering water. This is why although concrete itself is waterproof, the state still mandates that it must be waterproof.

Why does it still leak water after waterproofing?

Waterproofing is very similar to seeing a doctor. If you don’t see a doctor, you will definitely have a good outlook. The level of doctors is there, and some ordinary doctors are not good at it. You must have an expert account, and waterproofing is also the same. If you find an ordinary practitioner and a real expert in the industry, the results will definitely be different. Any industry has many ordinary practitioners, and there are few real experts. However, in the eyes of laypeople, anyone who works in this field is an expert. Therefore, many people look for professional waterproofing as just an ordinary practitioner. And we know where to look for experts when seeking medical treatment. Waterproofing does not have credit endorsements from institutions, and we rely solely on our own abilities to screen.

[xincwaterproof]

XINC waterproof asphalt coating composite self-adhesive roll waterproofing system！

Due to long-term outdoor exposure to wind, sun, and rain, the terrace has experienced settlement, cracking, design defects, material selection issues, and non-standard construction, resulting in leakage. Usually, leakage occurs at some detailed nodes such as the periphery of the pipe root, water outlet, and internal corner, with a small portion occurring at a certain point on the large surface.

For the leakage repair of the terrace, the coil process (hot melt process or self-adhesive process) and coating process are usually used. If the terrace area is less than 15 square meters, it is recommended to choose a coating process. If the area is too small, it is not convenient to use coiled materials for node processing, and more overlapping will increase the risk of leakage; If the area is above 15 square meters, both processes are acceptable. Regardless of the process chosen, it is necessary to clean the base layer to ensure full adhesion of waterproof materials to the base layer; During construction, it is necessary to first strengthen the internal corners, pipe roots, water outlets and other detailed nodes, and then carry out large-scale construction; During the construction of coiled materials, the overlapping edges, closing edges, etc. need to be sealed properly. During the coating construction, be careful not to miss the coating and ensure the thickness of the coating film.

Introduce a new method for waterproofing and maintenance construction of a terrace -XINC Waterproof the construction process of water-based asphalt waterproof coating composite self-adhesive roll, using a case study of a certain terrace leakage problem treatment.

The construction process of water-based asphalt waterproof coating composite self-adhesive roll material has many advantages over traditional roll material and coating processesSeamless and dense waterproof layer: The asphalt coating is fully adhered to the base layer, forming a seamless and dense waterproof layer that can cover 2mm cracks, and has strong adaptability to building structure settlement and cold and hot deformation. It solves the problem of water leakage in the lower part of the waterproof layer caused by the inability to achieve 100% full adhesion during the construction of hot melt or self-adhesive rolls;

Safety and environmental protection: water-based products, environmentally friendly, noiseless construction, no open flame construction, safe and convenient, avoiding the burning sensation of workers baking rolls in the hot summer;

Convenient construction: The application of asphalt coating is simple, without the need for technical work, and the drying speed of water-based asphalt coating is fast, greatly improving construction efficiency;

XINC Waterproof The asphalt coating composite self-adhesive roll waterproofing system is more reliable than a single coating construction process, with guaranteed waterproof thickness and better durability.

[xincwaterproof]

XINC Waterproof Decoration Diary: How to Select Waterproof Materials for Basements?

There are various types of waterproof materials, each with different advantages and applicability. In furniture engineering, there are four commonly used waterproof materials for bathrooms, kitchens, balconies, etc.: cement mortar, polyurethane, JS waterproof coating, and acrylic acid. So, let’s learn how to choose waterproof materials for the basement together!

Characteristics and applicability of basement waterproofing materials

2、 XINC Waterproof Polyurethane The polyurethane system can be used both indoors and outdoors, with a thickness of about 3mm and an elasticity of over 300%. The substrate will not crack even if it breaks, so it has good waterproof performance. The disadvantage is that it has a strong odor and is not environmentally friendly.

4、 XINC Waterproof Acrylic acid Acrylic acid series is a pure liquid, non-toxic, harmless, non flammable, and can be used after opening the lid. It is easily soluble in water and can form a strong waterproof layer due to wall cracks. Its performance characteristics are stable, the application effect is ideal, and the price is relatively friendly. It can be used for wall waterproofing, so it is very common in decoration waterproofing projects.

The function of the waterproof layer is to isolate external water sources, while the moisture-proof layer prevents moisture, not water. Due to the dampness in the south, once you return to the tide of the southern sky, you will see that the people decorating with ceramic tiles are all wet. So the two are different concepts. Due to the susceptibility of the exterior walls and bottom plates of basements to groundwater damage, moisture-proof and waterproofing issues are important issues that need to be addressed in basement design. Due to high environmental protection requirements, it is difficult to choose good polyurethane waterproofing materials on the market. If the quality of these materials does not meet standards, they will not be environmentally friendly. Therefore, overall, it is better to choose acrylic and JS waterproofing coatings.