Jignesh Sabhadiya

www.Engineeringchoice.com

[engineeringchoice]

Pulley: Types, Uses, Advantages & Disadvantages

Pulley: Types, Uses, Advantages & Disadvantages

The pulley is used to transmit power from one shaft to another via flat belts, V-belts, or ropes. Since the velocity ratio is the inverse ratio of the diameter of the driving and pulleys, the diameter of the pulleys must be carefully selected to be the desired velocity ratio. The pulley must be in perfect alignment to allow pulleys to travel normally in a row.

What is Pulley?

A pulley is…

View On WordPress

[engineeringchoice]

Ozone Layer: it's Causes, Effect & Control Measure

Ozone Layer: it’s Causes, Effect & Control Measure

While traveling for many reasons that cause global warming, the depletion of the ozone layer is one of its major reasons. To know more about the depletion of the ozone layer, we need to know what the ozone layer is. Let us dig deeper into the ozone layer, how it is formed, the causes and effects of ozone depletion, and measures to prevent it.

What is the ozone layer?

Our earth’s…

View On WordPress

[engineeringchoice]

Belt Drive: Types, Material, Advantages & Disadvantages

Belt Drive: Types, Material, Advantages & Disadvantages

What is a belt-drive?

The belt drive is a loop of flexible material that is used to mechanically connect two or more rotating shafts, most often in parallel. Belt drive can be used as a source of motion, to transmit power efficiently or to track relative movement. The belt drive is looped over the pleura and there may be a bend between the pleura, and the shaft does not have to be parallel.

View On WordPress

[engineeringchoice]

Lever | it's Definition, Principal, Types & Uses

Lever | it’s Definition, Principal, Types & Uses

Lever, a simple machine is used to increasing physical force. All the early people used levers in some form, to move heavy stones or to dig sticks for land cultivation. The principle of the lever was used in swaps, or shadows, with long levers, mounted on one end with a platform or container of water, hanging from the short arm, and attached to the long arm Was. A man could lift his weight…

View On WordPress

[engineeringchoice]

Deforestation | Its Causes, Effect & Control Measures

Deforestation | Its Causes, Effect & Control Measures

We have experienced and are also undergoing drastic climate change. Have we thought about the reasons for this drastic climate change? There are many reasons for this. The major reason is deforestation. Let us discuss the causes and effects of deforestation, deforestation, and also take measures to prevent it. Discussing all these, as it is said, “coin has two aspects”, there are also some…

View On WordPress

[engineeringchoice]

Acid Rain | its Causes, Effects & Prevention

Acid Rain | its Causes, Effects & Prevention

Acid rain or acid deposition is a very broad term that includes rain, snow, hail, or any type of precipitation with acidic components. When discussing acid precipitation, we need to discuss in detail what is acid precipitation, the term development, causes, how acid precipitation is measured, its harmful effects and prevention on plants, aquatic life, birds, and humans measure of.

What is…

View On WordPress

[engineeringchoice]

Greenhouse Effect | Causes & its effects

Greenhouse Effect | Causes & its effects

The term greenhouse effect has been discussed at a much broader level in this new era. Even though it is a heated discussion, very few of us know what it is and the causes and effects of the greenhouse. Let us bring all these subjects here under one topic for a better understanding of the greenhouse effect, its causes, and its effects.

What is the Greenhouse Effect?

The greenhouse effect is…

View On WordPress

[engineeringchoice]

Shaft | Definition, Types, Benefits & Limitation

Shaft | Definition, Types, Benefits & Limitation

What is Shaft?

The shaft is a rotating machine part, usually circular in cross-section, that is used to convey power from one part to another, or from a machine that produces power to a machine that absorbs power. The power to the shaft is distributed by some tangential force and the resulting torque (or twisting moment) installed within the shafts allows the power to be transferred to the…

View On WordPress

[engineeringchoice]

Shaft Coupling | Uses, Requirement & their Types

Shaft Coupling | Uses, Requirement & their Types

In general, shafts are available up to 7 meters in length due to inconvenience in transport. So as to have a maximum length. It becomes necessary to join two or more pieces of the shaft, so we need coupling to connect two or more pieces. In this article, we discuss what shaft coupling is, their types and benefits, and limits.

What is shaft coupling?

A shaft coupling is a device that is…

View On WordPress

[engineeringchoice]

Shaft Keys | Types, Material selection, benefits & Limitation of joint

Shaft Keys | Types, Material selection, benefits & Limitation of joint

The shaft keys are a piece of mild steel that is inserted between the shaft and the boss of the hub or pulley to prevent relative motion between them. It is always implanted parallel to the axis of the shaft. The key is used as a temporary fastener and is subjected to considerable crushing and shear stresses. The keyway is a slot or in the shaft and pulleys hub to accommodate a key.

Types of…

View On WordPress

[engineeringchoice]

Knuckle Joint | Modes of Failure and Application

Knuckle Joint | Modes of Failure and Application

A knuckle joint is used to connect two rods that are under the action of tensile loads. However, if the joint is guided, the rods may support a compressive load. A knuckle joint may be readily disconnected for adjustments or repairs. Its use may be found in the link of a cycle chain, tie rod joint for roof truss, valve rod joint with the eccentric rod, pump rod joint, tension link in bridge…

View On WordPress

[engineeringchoice]

Cotter Joint | Types, Modes of Failure and Application

Cotter Joint | Types, Modes of Failure and Application

Cotter joint is used to connect two rods subjected to axial tensile or compressive loads. It is not suitable to connect rotating shafts which transmit torque. Axes of the rods to be joined should be collinear. There is no relative angular movement between rods. Cotter’s joint is widely used to connect the piston rod and crosshead of a steam engine, as a joint between the piston rod and the tailor…

View On WordPress

[engineeringchoice]

What are locking Devices and their Function?

What are locking Devices and their Function?

What are Locking Devices?

 Locking devices are a mechanical component that prevents mated shafts and other machine elements from moving out of position when subjected to external forces. Operating conditions such as initial installation error, temperature variations, vibration, and others can all cause issues. These are critical components.

Ordinary thread fastenings, generally, remain…

View On WordPress

[engineeringchoice]

Rivet | Method & Types of Riveting, Benefits & Limitation

Rivet | Method & Types of Riveting, Benefits & Limitation

What is Rivet?

A rivet is defined as a headed pin or bolt of metal used for uniting two or more pieces bypassing the shank through a hole in each piece and then beating or pressing down the plain end so as to make a second head.

Rivets are a short cylindrical bar with a head integral to it. The cylindrical portion of the rivet is called the shank or body and the lower portion of the shank…

View On WordPress

[engineeringchoice]

What is Pipe Joint and their Types?

What is Pipe Joint and their Types?

What is Pipe Joint?

Pipe joints are integral to any piping system because it is not possible to have a continuous length of pipe for a pipe network. These joints can make or break a pipeline system depending on the resulting durability of the technique used to form the joint.

There are different materials of pipes use in the pipeline industry depending on the need and the type of product…

View On WordPress

[engineeringchoice]

Machine Design | Definition, Types Consideration, and Procedure

Machine Design | Definition, Types Consideration, and Procedure

In today’s modern world machine design is challenging day by day because of lots of options available in the market. So, there is challenging for a designer to design a machine with all these criteria as per below mention in this article. What is machine design, types of machine design, general considerations, and general procedure for machine design?

Definition of Machine design

Machine…

View On WordPress

[engineeringchoice]

Fossil Fuels | Types, Advantages and Disadvantages

Fossil Fuels | Types, Advantages and Disadvantages

Do you know what fossil fuels are? Do you know that fossil fuel is renewable? Still, thinking??? No worries… Here we deal with the question that fossil fuel, types of fossil fuel, pros and cons of fossil fuel, and also describe whether fossil fuel is renewable or non-renewable energy?

What are fossil fuels? Definition of fossil fuels

“Fossil fuels are made from decomposing plants and…

View On WordPress