I said Iâd write up a tutorial on how to make these wings. Itâll be terrible So, here goes. XD
Have one or two friends to help you out. Itâs easier with more hands.
Materials:
Thin poster board. (For small wings you will need 3 pieces. For wings like this you will need 6)
Opal cellophane. (two rolls to be safe)
Exacto knife. (I recommended using this for cutting out the poster board)
3 Hanger wires (itâs super sturdy)
Find a reference photo! These wings are meant for a Periwinkle cosplay but since her and Tinkerbell have the same wings we used Tink as a reference.
Since we made our wings super large we had to glue two pieces of poster board together. This is why I said 6 pieces for large wings. Reason why is because of their size just one piece would make it droop. So before drawing the design on you spray one piece with adhesive and put the other piece on top of it. Making it as even as possible.
If youâre making smaller wings just go to step three!
Draw your design on the poster board. We drew ours on from corner to corner (diagonally) If you want smaller wings I recommend drawing it from corner to the the middle of the board.
This is the most tedious of all the steps to making wings. Take your exact o knife and start cutting. You cut around the design but make sure to cut half an inch away from the line. You can go back later to make it thinner if you want. Using one poster board will take less time then two since it isnât as thick.
Make sure there is something underneath the board so you donât damage your floor.
Step Five: (not necessary but who says no to glitter)
Weâre obsessed with glitter. So naturally we coated both sides of the design with white glitter. We used adhesive for this as well.
Step Six: (Smaller wings donât need this but if you want to add it then go ahead!)
Take your wire hanger and bend it out so itâs the same shape of the wing that will be the closest to your back. Glue the wire down about 7 inches down from the tip of the wing. Most of the support is needed in the middle, and bottom of the wing.
Let some of the wire hang out of the bottom about four inches so you can connect the harness.
Roll out the cellophane to go over the wings. One piece for each side. Spray adhesive to the wing first and then gently place the cellophane over it. I recommend having someone help you with this part because adhesive is a pain when something goes wrong.
Do this for both the big wing, and the smaller one. Make sure the cellophane is over the wing evenly. Pat out any bubbles it may have.
When both sides have cellophane on it take your iron and make sure itâs on a low setting. You donât want it to burn or melt the cellophane. Gently go over the wing, and even it out as much as possible. There will be some bubbles, and such but think of it being more realistic.
Cut off any excessive cellophane but leave some near the veins and by the wire. If itâs to short the cellophane will come apart. We left little less then half an inch.
Take the adhesive to glue the little wing to the bigger one. You want to make sure you glue it on the inside.
Use another wire hanger and bend it into a rectangle. Wire hanger is tough to bend so youâre going to have to use your inner strength. Cut off any excess wire with a wire cutter. Cover it with electrical tape so it becomes sturdier.
Line up the wing wire with the harness wire at the spot where itâs needed. Take the wing and connect it to the harness. Using electrical tape to keep the two of them together. Cut off an excess wire so it doesnât dig into the wearers back.
Alas you have fairy wings!! I hope this helps a bit T-T Have fun!
Tip: You may have to cut a slit in the back of your outfit for the wings to slip into. Wearing a bra helps because it goes underneath it.
s-u-f-j-a-n-s-t-e-v-e-n-s
tangentwithtanner
discoholicmusic
prguitarman
amandla
pixelskylines
germansingergirl
