#kt200 ecu programmer

[auto-tools]

How to Clone Tricore ECU with FoxFlash/KT200 Tool?

FoxFlash & KT200 Programmer can support cloning ECU function as OBDSTAR DC706. This is an introduction to how to clone Tricore ECU with the new KT200 software step by step. The procedure may apply to FoxFlash software as well.

Step 1. Read ECU data via the "BOOT MODE TRICORE" or "BENCH TRICORE" option. Including Micro FLASH, and EEPROM data from the original ECU & new ECU.

Step 2. Select Menu >> Select Drive >> TOOL BOOT >> TOOLS BOOT MODE - INFINEON TRICORE Clone Service >> ECU Model

Step 3. Fill 1st option with original ECU Micro file, fill 2nd option with new ECU Micro file.

Step 4. Click "CLONE & SAVE" to save new ECU file.

Step 5. Select BOOT MODE >> INFINION TRICORE Boot >> ECU Model >> Load new ECU file >> Write to new ECU

BENCH TRICORE may cause incomplete writing of ECU data(Boot is recommended)

Attention 1. Please write the original EEPROM to new ECU with no changes; 2. Please write Micro FLASH & EEPROM data separately, CANNOT read & write together; 3. If the Micro FLASH data cannot be written, it needs to be processed manually with winols. Or asking help for a professional engineer. 4. Nonsupport VW 5th generation IMMO system.

Technical Support www.obd2shop.co.uk

[auto-tools]

KT200 ECU Programmer Added Offline Workstation USB

KT200 ECU Programmer Master Version has added a new feature to read & write ECU/TCU via OBD/Bench/Boot/BDM/Jtag offline. Without having to connect to the Internet, just plug the KT200 Offline Workstation USB Dongle to realize. This is very useful for outdoor ECU tuning where the Internet is too weak or not.

The black is the U disk. It contains software and installation instruction, which should be installed online before it can work offline. The white is the dongle to activate the first-time running.

Note: For KT200 Auto Version, users should upgrade to the full version before buying the offline workstation USB.

KT200 Reads JCB EDC17CV44 Offline on Bench Open KT200 software >> Select Driver >> BENCH MODE >> JCB >> TC1767-JCB >> EDC17 CV44 >> OK >> Connect Keep ECU power on. Click "OK". Read All >> Save Keep ECU power on. Click "OK". Reading in progress... wait until 100%. End of read, turn the dashboard off. Click "OK". Completed.

KT200 Reads Renault SID310 Offline by OBD Open KT200 software >> Select Driver >> Car obd >> JCB >> Renault >> Master >> 2.3 dCi SID310 "CAN >> OK

KT200 Reads VW EDC 16U31 Offline on Bench Open KT200 software >> Select Driver >> BENCH MODE >> Volkswagen >> MPC56 3/4 - VAG >> DIESEL EDC16 U31 >> Connect Keep ECU power ON. Click "OK". Read All >> Save Keep ECU power on. Click "OK". Reading in progress… wait until 100%. End of read, turn the dashboard off. Click "OK". Completed.

www.obd2shop.co.uk

[auto-tools]

KT200 V11.01 Software Free Download & Installation Guide

KT200 ECU Programmer's latest software version V11.01 has been released, here you can free download & a guide to install it.

Where to free download KT200 v11.01? Mega: https://mega.nz/file/NPM0GDZb#PVVHI2mXLekSAiRNd1UvHEom4wLtKcc64isJB7SV6m8 Weiyun: https://share.weiyun.com/T1ZVPy6u (password: zug4hj) Size: 38.7MB Compatible system: Win7, Win8/8.1 Win10, Win11.

How to install KT200 v11.01? Operating video:

Step1. Click the "KT200setup-11.01" package to install the software.

Step2. Install & update KT200 driver: Computer management >> Device manager >> DESKTOP-FSN5GTS >> Other devices >> DFBTech >> Update driver >> Browse my computer for drivers >> Selected "DFBTech_DRIVER" folder >> Next

Step3. Download software & diagram Start "KT200 Service" >> Download Software Start downloading software, the old version will be completely uninstalled and deleted! Click "Yes". Download finished, install or not? If you choose YES, the current version will be uninstalled before installation. Click "Yes". Yes, I accept the terms of the License Agreement! >> Next >> Next >> Finish Reset the device successfully!

Restart "KT200 Service" >> Download Diagram Start downloading documents! Yes >> Finish

Completed. Now you can start to use Full Version KT200 software.

www.obd2shop.co.uk

[auto-tools]

(Solved) KT200 software Cannot find 'DFB2XX.dll' Error

Problem: After installing the KT200 software, it cannot be opened or reinstalled and the message "Cannot find 'DFB2XX.dll'" is displayed. What should I do?

Solution: Copy the DFB2XX.dll file to the C:\Windows\SysWOW 64 directory, if it is a 32-bit system, the path is C:\Windows\System32

DFB2XX.dll file Download free:

Note: The files in this link are compressed packages, which must be unzipped before replacement.

For more technical support, please follow http://blog.obd2shop.co.uk/

[auto-tools]

KT200 10.01 Free Download & ECU Coverage New Update

Here www.obd2shop.co.uk provide the latest version of KTM200 10.01 software with free download link and ECU supported update content.

Where to free download KT200 10.01 https://mega.nz/file/MKd03YQA#wpv1vARRRYNx9dERkYbIIoPdoaEMrVErVVLRUJYJP4k Size: 885.6MB Operating system: Win7, Win8/8.1, Win10, Win11

KTM200 ECU Programmer New Features Tricore Clone Automatic Function Added automatism to clone the following control units with OTP zone adaptation and password: - MED17.5 AUDI - MED17.5.25 AUDI - MEVD17.4.2 CITROEN - EDC17 C08 HYUNDAI - EDC17 C53 HYUNDAI - EDC17 C08 KIA - EDC17 C53 KIA - EDC17 C66 MERCEDES BENZ - MEVD17.4.2 PEUGEOT - MED17.5 SEAT - MED17.5.25 SEAT - MED17.5 SKODA - MED17.5.25 SKODA - ME17.9.20 SMART - EDC17 C73 TOYOTA - MED17.5 VOLKSWAGEN - MED17.5.25 VOLKSWAGEN

New full system for Mercedes truck & CLAAS continental ACM/MCM Until now, the K-line MCM2 D1/D2 and ACM versions were supported. Full reading of MCM2.1 D3/D4 and ACM2.1 in CAN line is now also available.

- Reading and writing Micro - Reading and writing EEPROM - Recovery - Checksum

To enable full system communication in D4 hardware versions, it will be necessary to perform simple unlocking operations with the control unit open by performing bridges on the PCB. At the end it will be possible to close the control unit and read and write all the contents from the pinout. Follow the instructions in the operating manuals.

PSA HYBRID4 HV17.4 Bench Mode Per Centraline PSA HYBRID4 HV17.4 Full reading of Citroen/Peugeot HYBRID4 ECUs via pinout added. The ECU has 2 internal HCUs. - Reading and writing Micro HCU1 / HCU2 - Reading and writing EEPROM HCU1 / HCU2 - Recovery - Checksum

Boot Mode (BAM) for EMS S8 e CRD2 We have added new BOOT MODE (BAM) for complete control unit management on SCANIA: - CONTINENTAL EMS S8

and new BOOT MODE (BAM) for MERCEDES BENZ / FCA with control units: - DELPHI CRD2.xx (Versioni SOLENOID e PIEZOTEC)

This makes reading and writing ECU in open mode easier compared to the previous JTAG mode (JTAG function still available). Furthermore, with this method, it's no longer necessary for Delphi CRD2.xx SOLENOIDs to open the ECU from the underside. - Reading Micro + Eeprom - Writing Micro + Eeprom - Recovery - Checksum

New Automatic Function: Tricore Clone Added automatism to clone the following control units with OTP zone adaptation and password: - BMW MEVD17.2.8 - BMW MEVD17.2.H - FIAT DCU17 PC42 - MERCEDES BENZ EDC17 CP10 - MERCEDES DCU17 PC42 - MINI MEVD17.2.8 - MINI MEVD17.2.H - RENAULT DCU17 PC42 - VOLVO EDC17 CP48

Continental GPEC2, GPEC3, GPEC4, GPEC4LM ! New BOOT MODE (BAM) for ECUs Continental GPEC fitted on vehicles FCA Fiat, Jeep, Chrysler, Dodge: - Continental GPEC2A - Continental GPEC3 - Continental GPEC4 - Continental GPEC4LM - Reading Micro + Eeprom - Writing Micro + Eeprom - Recovery - Checksum

Cummins CM2200 Dodge Chrysler Added JTAG MODE for control unit Continental Cummins CM2200 for vehicles Dodge And Chrysler. - Reading - Writing - Recovery - Checksum

New Boot Modes For Delphi DCM7.1 A/B PSA Boot Mode Solution For Delphi ECU DCM7.1A / DCM7.1B Added New Boot Mode for micro AURIX TC297 for ECUs DCM7.1A and DCM7.1B mounted on PSA group cars. - Reading - Writing - Recovery - Checksum

Updates for JTAG - Bench - OBD - New boot via pinout for Mitsubishi Outlander 2.0 Petrol - Read and write - Recovery - Checksum Added JTAG mode for Adblue ACM Volvo Trucks Euro 6 control unit - Read - Writing - Recovery - Checksum

Added to the OBD driver for Marelli 9DF FCA also the VIRTUAL reading, in addition to the real reading already present.

Exclusive! - Full System for Marelli 9GF and 8GSW sw version from 2020 - Full System Marelli 9GF for software version from 2020 - Full System Marelli 8GSW for software version from 2020

Added new full system drivers for Marelli 9GF and Marelli 8GSW control units for versions with software update blocked since 2020. On these control units with updated software was no longer allowed the complete reading of micro and eeprom from pinout.

Is now possible: read and write the complete content without opening the control unit. - Reading and writing Micro - Reading and writing EEPROM - Recovery - Checksum

www.obd2shop.co.uk

[auto-tools]

KT200 ECU Programmer + Bench Box Self Test

KT200 ECU Programmer supports ECU maintenance chip tuning, remove DTC codes, OBD/BOOT/BDM/JTAG & multiple protocols. This is a guide on how to do self test with KT200 + Bench Box.

Video guides:

1. Connect KT200 & BENCH BOX to PC.

2. Start KT200 software: Select driver >> BENCH MODE >> TOOLS BENCH MODE >> TEST for BENCH BOXES >> TEST BENCH BOX V.2 >> INFO Here you can check the operation notice.

This driver is useful for testing the Bench Box V.2 During the test: - the relays will be triggered at different speeds. - the read LED will flash several time ... Before launching the driver, connect the Bench Box V.2 to the tool and power it through the round jack of the bench box itself or from the round jack of the DFOX tool.

3. OK >> Start Test KT200 will start reading automatically... Connect Bench Box without ECU and power it, click "OK". Wait processing until 100%. Test End. Completed.

KT200 ECU Programmer + Bench Box Self Test | OBD2shop.co.uk Official Blog KT200 ECU Programmer + Bench Box Self Test