Xhorse UK

[auto-tools]

YANHUA ACDP + Module 45: VW DQ38x Gen2 Gearbox Mileage Correction

Resetting Volkswagen gearbox data is now faster and safer. Use the YANHUA Mini ACDP + Module 45 for seamless DQ38x Gen2 (0DE/0GC) mileage and time correction. This professional solution supports 2022+ VW models using a specialized interface board—no soldering required. Achieve precise calibration and reliable data backup in just a few clicks.

Preparation & Connection 1. Hardware Setup: Locate the original gearbox connector under the hood and replace it with the SH725xx-0DE interface board. 2. Configuration: Move the jumper cap to the "CAN-R" position. 3. Power & Link: Connect the ACDP to the gearbox using a standard 12V adapter (current ≥ 2.5A) and power on the device. 4. App Sync: Open the Mini ACDP app and verify the device connection status in the upper right corner.

Operational Steps Identify System: Navigate to VW/AUDI > Gearbox mileage correction > VW > DQ38x_GEN2(0DE/0GC) > Identify info. Screenshot the current mileage and system runtime for your records.

Mileage Correction: Select Mileage correction (auto mode). The app will automatically back up the EEPROM data before allowing you to enter the new mileage value.

Time Correction: Choose Time correction (auto mode). After another automatic backup, enter the desired system runtime to match the new mileage.

Finalize: Once the "Calibration finish" message appears, verify the new data and disconnect the hardware. Important: Never disconnect power or remove the device while the app is writing chip data to avoid module damage.

www.obd2shop.co.uk

[auto-tools]

How to Activate and Download Software for TOPDON RLink J2534

This post shows how to activate and download the software for the TOPDON RLink J2534 diagnostic tool.

1. Download and install the RLink Platform software on your PC. Go to www.topdon.com. Click on Diagnostic Tools > RLink J2534, then click Download.

Note: It is recommended to disable your antivirus software during installation. Since the RLink Platform serves as the driver management platform for OEM software, it may be mistakenly removed by antivirus software.

2. Launch the RLink Platform software. Register or log in to your TOPDON account. Connect the RLink J2534 to a PC using the included USB 2.0 cable. Then, click "Bind and Activate" to activate the RLink J2534. Note: Update the firmware to the latest version after binding the device.

3. Click on Driver Management > Driver Download to download the specific driver for your OEM diagnostic software. Note: The list of drivers depends on the actual product configuration.

Note: To ensure program stability, download the driver corresponding to the OEM software currently installed on your PC. Do not download drivers that are unrelated to your OEM software.

4. Click on Driver Management > Driver Info after downloading the driver. Then, click to open the newly downloaded driver and select the RLink mode.

Note: The illustrations and screenshots used in this Quick User Guide may differ slightly from the actual product due to ongoing product improvements.

For further information, please contact www.obd2shop.co.uk.

[auto-tools]

How to use TOPDON ArtiDiag600 S to do an oil reset for GMC Yukon

This post will show you how to use TOPDON ArtiDiag600 S to do an oil reset for a 2007 GMC Yukon Denali. As you can see, the change engine oil soon indicator is on in the dashboard.

Insert the serial connector into the vehicle's OBD2 port and turn the ignition on without starting the vehicle

Turning the ignition on will initiate the tool; the tool will come up to the home screen. Then we choose [Maintenance] >> [OIL].

The tool is going to tell us that it is connecting to the vehicle.

Select the type of vehicle, then choose [Software Reset] >> [Automatic Scan]. This is verifying the information about a GMC.

Now, to make sure that the vehicle is stopped, the engine is off, and the ignition is on. Engine Oil Life Current Value: 0% Press The Confirm Button To Continue The Process.

Now we need to input the life we want for the oil.

Performed successfully.

Video guides:

www.obd2shop.co.uk

[auto-tools]

How to Sync Original Data to KEYDIY C29AX71 Smart Key by KD-X4?

Learn how to quickly synchronize and clone original key data using the KEYDIY KD-X4, 13# Remote Chip Reading Adapter, and C29AX71 Smart Key. This method enables seamless key addition without complex on-board programming, making it ideal for water-damaged keys or vehicles with difficult learning procedures.

Thechip synchronization now supports the NCF29AX series, including NCF29A1, NCF29A4, NCF29A2, NCF2953, NCF29A3and NCF2954.

Required Tools & Preparation Ensure the following hardware and software are ready before proceeding: Main Devices: KEYDIY KDX4 or KD MAX. Specialized Key: KEYDIY C29AX71 Smart Key. Adapter: KEYDIY 13# Remote Chip Reading Adapter. Software: Update your KD App to the latest version before proceeding.

Note: This is not a simple read-and-copy procedure; some keys require chip removal and soldering. There is no need to generate a remote program before reading the original key data.

Step-by-Step Synchronization Guide 1. Extract the Original Chip Disassemble the original vehicle smart key and carefully remove the NCF29AX series chip.

2. Attach the Chip to the #13 Adapter Solder the chip onto the 13# Adapter and connect it to your KD-X4 or KD-MAX. Alternative Method: Follow the provided wiring diagram to solder wires directly to the keyboard to read and save data without removing the chip.

3. Synchronize via KD App Navigate to: Remote function >> Smart key clone >> Universal smart key synchronization>> Read Chip data. This process syncs the original chip’s remote data and key ID to the CAX and CA7 series.

4. Write to C29AX71 Smart Key ① Connect C29AX71 Smart Key to the KD-X4 using the 6-pin programming cable. ② Select "Generate dealer keys". ③ Once finished, snap the key shell onto the new hardware.

Final Results & Advantages The primary advantage of this method is efficiency. After writing the data, the new key works directly on the vehicle with no additional programming required. Always test both the new C29AX71 Smart Key and the original key to confirm all functions operate normally.

www.obd2shop.co.uk

[auto-tools]

LAUNCH X-431 Heavy Duty Update: Scania, Iveco & Caterpillar Support

The latest Heavy-Duty Diagnostics Software Update for the LAUNCH X-431 series is now available. This release expands heavy-duty vehicle coverage, adds new special functions, and improves diagnostic performance across compatible devices, such as X-431 PAD 5 and PRO3 Link HD.

Important: Activation Requirements To access these diagnostic features and perform future upgrades, your device must have an active Heavy Duty (HD) Software Authorization and be within the Subscription Service's validity period.

Update Highlights This version focuses on stability improvements and specific special functions for major commercial vehicle brands: 1. SCANIA (V16.20): Added 35 new special functions; added TCO and AMS2 data streams; optimized overall system stability. 2. HD_IVECO (V22.15): Added Gateway Module support; integrated MD1 CS069 and MD1 CE101 systems; added maintenance functions for 2019+ Daily models. 3. WP_DIESEL (V12.80): Major expansion for Weichai self-developed WISE10 to WISE18 series; optimized WISE15 system cylinder cutoff test. 4. HD_TATA (V10.75): Added basic functions, actuation tests, and special functions for EMS, ABS, EPAS, and ESC on TATA BS6 models. 5. HD_KNORR (V10.30): Added basic and special functions for TEBS4 CAN, TPMS, and TEBS4 K systems; fixed known software issues. 6. HD_CATERPILLAR (V12.50): Added Manual Aftertreatment Regeneration and Vibratory System Test. 7. HD_DETROIT (V12.90): Added parameter menu and new special features. 8. DELPHI (V12.70): Added support for Dongfeng Delphi Ruiqi M9T and Changcheng Delphi DCM7.24; optimized Active Tests. 9. EV_HD_GEELY (V10.80): Added diagnostic functions for LCV/XingXiang V7E and V8E (N72 Facet).

www.obd2shop.co.uk

[auto-tools]

New Free Upgrade: OBDSAR TCM Cloning for DQ38X/DQ500 GEN2

OBDSTAR has just released a powerful FREE software upgrade for the KeyMaster G3 and DC706, significantly expanding its TCM (Transmission Control Module) cloning capabilities. This update focuses on the high-demand Bosch and ZF GEN2 series, making maintenance and repair even easier for professional workshops.

Key Highlights of the Update: 1. Comprehensive Support for BOSCH GEN2 Users can now perform Data Read/Write, Mileage Calibration, and IMMO Data Decryption (Exclusive) via Bench Mode for the following models:

DQ380 (0DE/0GC) DQ381 (0DE/0GC) DQ500 (0DL) Recommended Wiring Cable: TCM-005

2. Enhanced ZF Support The update also includes Data Read/Write functionality for:

ZF AL552 GEN2 Recommended Wiring Cable: TCM-024

Supported Vehicle Brands: This update covers a wide range of VAG group vehicles and luxury brands, including:

Volkswagen & Audi Skoda & Bentley Lamborghini & Porsche

Technical Specs: Supported Bootloader Version: BH1G0401 Method: Bench Mode (No need to disassemble the unit, ensuring a safer and faster process).

How to Get the Update? This is a FREE upgrade for all active KeyMaster G3 and DC706 users. Simply connect your device to Wi-Fi and run the update manager to download the latest software version.

Upgrade today and stay ahead in the world of advanced TCM programming!

www.obd2shop.co.uk

[auto-tools]

TOPDON ONE Lite vs. TOPDON ONE vs. TOPDON ONE Plus

Choosing the right diagnostic tool can significantly impact your workflow efficiency and service capability. In this article, we compare three popular models — TOPDON ONE Lite, TOPDON ONE, and TOPDON ONE Plus — to help you quickly understand their differences and find the right fit for your needs.

Hardware Overview All three devices share the same core hardware platform, making them equally capable in terms of performance and daily operation.

Summary: Hardware is identical across all models — the real differences lie in software capabilities.

Core Diagnostic Functions All three tools support full OBDII functionality and complete system diagnostics.

Summary: No compromise here — even the Lite version delivers full diagnostic capability.

Advanced Features Comparison This is where the real differentiation begins.

Summary: ONE Lite: Entry-level coding only ONE: Adds basic customization ONE Plus: Full-featured professional tool with IMMO and programming

Conclusion: Which One Should You Choose? TOPDON ONE Lite: Best for entry-level technicians or workshops that need reliable diagnostics without advanced features. TOPDON ONE: A balanced option with added customization functions — suitable for growing workshops. TOPDON ONE Plus: The most powerful option, ideal for professional technicians who require ECU programming, IMMO functions, and broader vehicle coverage.

In short, if your work involves deeper vehicle access and advanced operations, ONE Plus is the clear choice. Otherwise, ONE Lite and ONE still provide excellent value with full diagnostic capability.

www.obd2shop.co.uk

[auto-tools]

How to Add 2025 BYD Formula Leopard Ti7 Key with Lonsdor K518 Pro?

Adding a new smart key to the 2025 BYD Formula Leopard Sealion 7is a straightforward process when using the Lonsdor K518 Pro. This guide provides a concise, step-by-step walkthrough of the programming procedure.

Preparation and Tools Needed Before starting, ensure you have the following items ready: Lonsdor K518 Pro Key Programmer OBD communication cable Original car key and the new smart key A stable internet connection

Step 1: Generate the Smart Key First, you must prepare the new key to be recognized by the vehicle’s system. 1. Navigate to Generate Smart Key > BYD > Formula Leopard >Sealion 7 2025 ID4A 2. Place the new key into the K518 Pro's card slot. 3. Click Generation and wait for the "Generated successfully" message.

Step 2: Read Data and Password To access the immobilization system, you must retrieve the vehicle's security data. 1. Locate and remove the cross-domain platform box located below the steering wheel to facilitate password reading. 2. On the K518 Pro, select Immo & Remote > BYD >Smart Key > Formula Leopard Series > Sealion 7> 2025- > Program smart key 3. Follow the on-screen prompts: Turn off the ignition and turn on the hazard lights (flashing lights). 4. Select Method 3: Disassemble the left EEPROM of the CEM module to obtain the 32-bit PIN code 5. The device will read the EEPROM data. Once successful, save the file to your device.

Step 3: Program the Smart Keys Note: All keys not present during this process will be deleted from the system. You can program up to 4 keys total. 1. Select the saved EEPROM file to begin programming. 2. Program Key 1: Place the first key (original) in the vehicle's sensing area and click OK until "Program complete" appears. 3. Program Key 2: Place the second key (new) in the sensing area and click OK. 4. Once both keys are registered, click Cancel to finish the session.

Step 4: Verify Functionality Always test both keys to ensure the immobilization and remote features are working perfectly. Engine Start: Press the brake and the Start button with each key individually to confirm the engine starts. Remote Features: Test the Lock and Unlock buttons on both the original and the new smart key. The programming for your 2025 BYD Formula Leopard Sealion 7 is now complete.

www.obd2shop.co.uk

[auto-tools]

New Release: KEYDIY OBD Cable for Ford Alarm Reset & All-Keys-Lost

The new KEYDIY OBD Function Extension Cable is a dedicated hardware solution for Ford alarm reset (2015–2018) and All-Keys-Lost programming (2018–2022). Designed for stability and speed, this professional harness bypasses modern security hurdles and includes built-in interfaces to support future updates for Toyota and NIO vehicles.

Core Solutions Ford Specialist: Essential for Alarm Reset/Override (2015–2018) and All-Keys-Lost (2018+). EV Ready: Built-in interface for New Toyota and NIO vehicle matching. Third-Party Compatible: Works seamlessly with various diagnostic devices for New Energy Vehicles. Stable Power: Includes a 12V interface to prevent voltage drops during programming.

KEYDIY OBD Extension Cable Ford Support List Everest - Intelligent Key System - (2016-2019) Taurus - Intelligent Key System - (2016-2019) Raptor F-150 - Intelligent Key System - (2015-2017) Raptor F-150 - Intelligent Key System - (2017-2020) Raptor F-150 - Intelligent Key System - (2018-2019) Raptor F-250 - Intelligent Key System - (2016-2020) New Mondeo - Intelligent Key System - (2016-2020) Escape - Intelligent Key System - (2020) Edge - Intelligent Key System - (2016-2020) Explorer - Intelligent Key System - (2016-2020) Mustang - Intelligent Key System - (2016-2020) EcoSport - Intelligent Key System - (2018-2020) Ranger - Intelligent Key System - (2016-2020) EcoSport - Intelligent Key System - (2018-2022) EcoSport - Mechanical Key System - (2018-2022) Escape - Intelligent Key System - (2020-2022) Escape - Mechanical Key System - (2020-2022) Escort - Intelligent Key System - (2018-2022) Escort - Mechanical Key System - (2019-2022) Expedition - Intelligent Key System - (2020-2022) Explorer - Intelligent Key System - (2020-2022) New Focus - Mechanical Key System - (2018-2022) New Focus - Intelligent Key System - (2018-2022) Mustang - Intelligent Key System - (2020-2022)

Why Add This to Your Kit? 1. Skip the Workarounds: Directly bypass alarm locks on Ford systems. 2. Future-Proof: Support for upcoming NIO updates and Toyota protocols. 3. Reliability: High-quality connectors designed for heavy workshop use.

Upgrade your tool kit with KEYDIY. Professional tools for professional results.

www.obd2shop.co.uk

[auto-tools]

2021 Ducati Diavel 1260 PIN Code Reset Function Procedure

Background PIN Code Overview The DUCATI PIN code is a 4-digit security password designed for immobilizer (IMMO) protection and anti-theft data programming.

Its main functions include: 1. Emergency Unlock If the key transponder fails, the smart key battery is dead, or the immobilizer system malfunctions, the PIN code can be entered via the dashboard to unlock and start the vehicle.

2. Security Protection Factory default PINs (e.g., 0000) are typically generic. Users are strongly advised to change the PIN to a personalized code via the dashboard menu to prevent unauthorized access.

3. System Recovery If the PIN is lost or not properly stored, the vehicle may be unable to start or access certain dashboard functions. In such cases, the PIN Code Reset function must be performed using a diagnostic tool.

Preparation Required tools: MOTOMASTER Diagnostic Tool M001A Adapter M041 Cable

Solution Use OBDSTAR MOTOMASTER to perform the [PIN Code Reset] function and restore the default PIN.

Detailed Procedure Step 1: Enter Diagnosis Menu Select: [MOTO Diag] → [DUCATI] → Latest Version → [Diagnosis]

Step 2: Select Model Choose: [By Model]

Step 3: Select Vehicle Information Follow this path: [D] [Diavel 1260 E5] [1262] [MY 21]

Step 4: Manual Selection Click: [Manual Selection]

Step 5: Enter System Select: [Hands Free (Smart Key)] → [Enter]

Step 6: Access Special Function Click: [Special Function] Enter password: 123 Click [OK]

Step 7: Reset PIN Code Select: [PIN Code Reset]

Step 8–9: Confirm Operation Click [OK] to confirm each prompt.

Step 10: Completion Operation completed successfully. The PIN code has now been reset.

You can now proceed to set a new PIN via the dashboard.

Manual PIN Change Procedure After resetting, follow these steps to set a new PIN: 1. Turn the ignition switch to the ON position. 2. Wait for the dashboard home screen. 3. Press and hold the MENU ENTER button on the left handlebar to access the menu.

4. Select [PIN CODE] 5. Enter the default PIN: 0000 6. Set your new PIN code to complete the process

Summary The PIN code is essential for immobilizer security and emergency access. If the PIN is lost or invalid, use MOTOMASTER to reset it. Always set a personalized PIN after resetting to ensure vehicle security.

Important: Please strictly follow the prompts on your diagnostic device during the operation process to avoid errors.

www.obd2shop.co.uk

[auto-tools]

GODIAG IM001 User Guide: How to Reuse Locked Toyota/Lexus Smart Keys?

The GODIAG IM001 is a professional-grade device designed to reuse locked Toyota and Lexus smart keys. By using innovative non-destructive technology, it bypasses the need to unlock or reset keys to a blank state, saving time and reducing costs.

Product Overview The IM001 features a compact design with integrated sensing areas and status indicators: 1. Chip Simulate Area: For vehicle communication. 2. Key Sensing Area: Where the locked key is placed. 3. Button: Used for power and operation. 4. Status Light: Indicates device activity. 5. Type-C Port: For charging and power.

Core Specifications Supported Models: Toyota/Lexus 4A, AA, BA. Connectivity: Bluetooth BLE 5.0 and a dual-core ARM processor. Power: Built-in 3.7V 450mAh battery or 5V DC external power. Dimensions: $61.5 \times 96.5 \times 12.5$ mm.

Operation Guide Follow these three simple steps to reactivate a locked key:

Step 1: Simulate Key Generation Place the locked or accidentally deleted key in the Key Sensing Area (2). Press the Button (3). The IM001 will read the secure identifier and internally simulate a matching key.

Step 2: Match to Vehicle Use the IM001 device itself as the replacement key during the standard vehicle matching process. The device writes the ID and necessary data into the vehicle's system while capturing the required passwords.

Step 3: Write-Back Operation Once the data is retrieved, the IM001 writes the complete information back to the original locked key.

Final Confirmation: Test the original key on the vehicle to ensure all functions are restored.

Indicators & Controls Status Light Meanings

Button Functions Power On/Off: Long-press for ~3 seconds. Status Inquiry: Short-press while on to hear a voice prompt of the current status. Reset: Long-press for ~5 seconds.

Maintenance & Warranty Warranty: 1-year limited warranty from the date of purchase. Care: Avoid improper voltage, unauthorized modifications, or harsh environments (water/extreme heat). Operating Temp: -10℃ to 50℃.

www.obd2shop.co.uk

[auto-tools]

Lonsdor K518 Pro Wring Diagrams for BMW BDC3 & VAG 5C/5D

The Lonsdor K518 Pro Key Programmer, when paired with the Encrypted Solder-Free Adapter Kit, provides a powerful solution for reading encrypted data across premium vehicle brands. This setup enables advanced programming for BMW G/U chassis systems and smart key reading for VW, Audi, and Porsche.

Software & Licensing Requirements To utilize these features, ensure your device meets the following criteria: K518 Pro Full Version: The device must have an active subscription period to function. K518 Pro FCV: This specific version requires the manual activation of the BMW BDC License and the VW MQB49 5C 5D License.

Technical Wiring Diagrams A proper connection is vital for successful data reading. Reference the diagrams below for specific vehicle modules:

BMW G-Chassis /U-Chassis with LCD Screen:

Volkswagen 5C/5D Systems

Audi 5D Systems

Porsche 5D Systems

www.obd2shop.co.uk

[auto-tools]

OBDSTAR Marine Diagnostic Software Upgrade: New BRP Support Added

OBDSTAR has released a significant upgrade to its marine diagnostic software, introducing support for BRP.

BRP Software Functions: 1. Supports IMMO and service functions for all models up to 2025. 2. Supports CDID diagnostics for 2014 and newer models, allowing users to view specific model, year, version, configuration, and other details. 3. Adds the following special functions: Set Engine Serial Number Set Vehicle Total Hours Set VIN Reset Last Maintenance Set Vehicle Model Number Configure Keys Set Customer Name Set Delivery Date Configure iBR (Lock/Unlock Calibration)

Supported Tools: MarineMaster ISCAN SEA-DOO (MARINE) D800 MS80 D700 ISCAN BRP

Software updates may vary depending on product configurations. For more details, please contact: www.obd2shop.co.uk

[auto-tools]

Launch X431 PAD VII Elite: How to Get Technical Support

The Launch X431 PAD VII Elite is designed to provide users with robust support options, ensuring that help is always available when you need it. Whether you require live technical assistance or a remote diagnostic session, the process is straightforward and user-friendly.

Live Technical Support To connect with a support representative, simply power on your X-431 PAD VII Elite and select the IM Customer Service button in the upper-left corner of the interface. Live technical support is available to assist you directly during the following hours: Monday to Friday 8:00 AM to 8:00 PM (China Time) This 12-hour window ensures that you have access to expert help throughout the business day.

AI Intelligent Customer Service For added convenience, an AI Intelligent Customer Service feature is scheduled for release. Once launched, this tool will provide instant responses to common customer inquiries, helping you resolve issues quickly without waiting for live assistance.

Language Support To accommodate users from different regions, the system allows you to translate the interface into your preferred language, ensuring clear communication and ease of use.

Remote Assistance For more complex diagnostic issues, you can also request remote support. By initiating a remote connection, a professional technical support specialist can access your tablet and assist in diagnosing the problem directly, saving you time and effort.

For more information about the device or to explore additional resources, visit www.obd2shop.co.uk.

[auto-tools]

How to Add VW Audi Porsche 5C/5D Key with Yanhua ACDP & Module 44?

This tutorial provides a concise guide to adding a VW, Audi, or Porsche 5C/5D key using the Yanhua Mini ACDP and Module 44. Follow these streamlined steps to complete the programming process efficiently via OBD and ICP modes.

Preparation & Connection

OBD Connection: Plug the ACDP into the vehicle's OBD interface using the OBD cable.

Ignition: Turn on the ignition and ensure the instrument cluster is lit.

Device Binding: Open the ACDP app and confirm that the programmer is successfully bound in the top-right corner.

Watch Video Tutorial:

Step 1: Identify Vehicle & Key Information

Path: Navigate to VW > VW MQB IMMO(ODO)> MQB49 IMMO(5C/5D).

OBD Identify: Select OBD identify info to verify car data.

Documentation: Take screenshots of the key ID and quantity for your records.

PCF Read: Place the original key into the PCF adapter and click “PCF read key info” to verify its ID.

Note: If prompted, perform an adapter upgrade under “Special Functions> Adapter Upgrade > PCF-KEY Upgrade" before proceeding.

Step 2: ICP Data Reading & Dealer Key Preparation

Disassembly: Disassemble both the original and new keys to access the circuit boards.

Read Key Data: Connect the original key plate to the interface board and ACDP. Select ICP+OBD add key > VW 5C Magotan >Step 1: ICP read work key, and save the backup file (ensure it ends in .bin).

Write New Key: Replace the original key plate with the new blank key plate. Select Step 2: ICP write new key, load the previously saved .bin file, and click Make dealer key.

Step 3: Modify Key ID (Optional but Recommended)

Function: Go to Special Function > ICP modify key ID.

Adjustment: Enter the "lost" key ID found in your previous OBD screenshots.

Purpose: This ensures the vehicle can be programmed normally in the future. Do not modify it to the working key ID.

Step 4: OBD Key Learning

Restore: Reassemble the keys with batteries, turn on the ignition, and open the vehicle hood.

Start Learning: Select Step 3: OBD Learn key and load the original car data file.

Key Quantity: Enter the total number of keys to be learned (e.g., "2").

Induction: Place each key near the induction coil one by one as prompted.

Confirmation: The instrument cluster will display the learning progress (e.g., 2-2) once complete.

Final Check: Verify that both the original and new keys start the vehicle and operate all remote functions properly.

www.obd2shop.co.uk

[auto-tools]

Xhorse VVDI All-In-One Garage Remote (XKGTF1EN) Pre-Order

The new Xhorse VVDI All-In-One Garage Remote (XKGTF1EN) is now available for pre-order and expected to ship in 30 days. This professional 3-in-1 solution replaces three separate remotes for garage doors, electric gates, and rolling shutters. Supporting 300MHz-916MHz and ASK/FSK codes, the XKGTF1EN simplifies the duplication process for locksmiths and technicians worldwide.

Core Functional Highlights 3-in-1 Capability: Supports copying three different frequencies and datasets simultaneously, allowing users to control multiple systems with one hardware unit. Automatic Frequency Matching: No manual adjustment is necessary. The device automatically detects and adapts to original frequencies ranging from 300MHz to 916MHz. Extensive Protocol Support: Fully compatible with both ASK and FSK codes. Advanced Code Copying: Supports fixed codes (PT22XX, HT6P20, VD5026, etc.) and rolling codes (HCS101, HCS30X, HCS36X) with factory code input. Broad Application: Generates or copies remotes for over 200 types of garage doors, rolling shutters, parking locks, and electric bikes.

Technical Specifications & Compatibility Product Name: XKGTF1EN Garage Remote Part Number: XKGTF1EN Frequency Range: 300MHz - 916MHz Supported Codes: Fixed Code, Rolling Code, ASK, FSK, Non-standard codes

Professional Configuration via KEY TOOL Series To maximize the utility of the XKGTF1EN, advanced functions such as cloud copying, cloud backup, and remote generation require integration with Xhorse KEY TOOL series equipment (such as the VVDI Key Tool Max Pro or Key Tool Plus). This allows for precise configuration adjustments, including frequency, key mapping, and baud rate.

For professionals looking to streamline their stock and provide a reliable, universal solution for gate and garage access, the Xhorse VVDI Garage Remote is an essential addition to the 2026 product catalog.

Note: Pre-order customers will receive priority shipping once the first batch arrives in our warehouse next month. Contact us today for bulk pricing and availability.

www.xhorsetool.co.uk

[auto-tools]

New KESS3 DataLogger: Real-Time Diagnostics & Tuning Now Included

Alientech has officially launched the DataLogger—a major functional update for the KESS V3 ECU & TCU Programmer. This feature shifts vehicle testing from subjective "feel" to objective, data-driven precision, allowing workshops to make tuning decisions based on real-time evidence rather than assumptions.

Built-In, Not An Add-On One of the most significant aspects of this update is its accessibility. The DataLogger is not an optional add-on; it is fully integrated into the KESS3 ecosystem. It is available to all users with an active subscription. This means KESS3-equipped workshops can deploy a professional-grade data acquisition system immediately without purchasing additional hardware or software.

Key Features of the New DataLogger Real-Time OBD Acquisition: Capture critical ECU diagnostic signals directly via the OBD port while driving or on the dyno. Integrated GPS Tracking: Automatically logs vehicle position, speed, and satellite precision, along with engine parameters. Intelligent Presets & Thresholds: Save custom signal lists and set minimum and maximum limits. Values exceeding these ranges are highlighted in red for instant error detection. Marker System: During a session, set up to three custom "Markers" to tag specific events or driving conditions for later analysis. Cloud-Based Dashboard: Logs are automatically uploaded to the Alientech Cloud for storage, interactive analysis, and sharing via secure links.

Professional Benefits for Tuners Precise Validation: Confirm the impact of your tuning maps with real-world performance data. Faster Troubleshooting: Monitor multiple diagnostic channels simultaneously to understand vehicle behavior quickly. Seamless Collaboration: Share data logs with partners or export them to CSV format for external analysis. Reliable Offline Mode: If the internet is unavailable, data is buffered on the KESS3 hardware and uploaded automatically once a connection is restored.

Technical Summary Availability: Included with active KESS3 subscriptions. Hardware Required: Standard KESS3 (no extra modules needed). Platform: Controlled via Alientech Suite with Cloud Dashboard support.

www.obd2shop.co.uk