#ledcontroller

[adafruit]

BIG BIG rainbows on "Sparkle motion" WLED driver board 🌈💡

We got our WLED-friend PCBs

https://blog.adafruit.com/2024/12/02/leftovers-layout-wled-board-revision-a-completed/

and are testing it with various LED grids. First, we tried out a 16x16 NeoPixel grid that runs on 5V. Since that worked well, we're now onto a much bigger 60 x 60 grid - that's 3,600 LEDs! These are some NeoPixel pebble

Adafruit NeoPixel Pebble / Seed LED Strand - 200 LEDs - 2" Pitch

We have all sorts of LED strips for a wide range of needs. Chonky strips? We got those! Strips with alligator clips&nbsp

netting samples we're also testing at the same time; each one has 20 x 60 pixels and uses 12V power, so it's a good test of the DC pass-through for higher voltages. Since WLED has a limit of 2000 pixels per output, this demo uses the three output ports that are then 'merged' together in memory to make a single large grid. We have more to test soon: the onboard IR receiver, USB PD, I2S microphone, extra I/O pins, and I2C, so watch for those videos as they come together. Coming soon -

Adafruit Sparkle Motion - All-In-One WLED and xLights Board

Coming soon! We're designing a board for using WLED - and we want to make like the bestest board in the wholeworld. Our resident me

[adafruit]

mini Sparkle Motion prototype - a tiny, fully-featured WLED board ✨🔌📏💡🌈

We're doing a lot of serious testing with our WLED mega-board, code-name Sparkle Motion .

Adafruit Sparkle Motion - All-In-One WLED and xLights Board

Coming soon! We're designing a board for using WLED - and we want to make like the bestest board in the wholeworld. Our resident me

While doing some holiday lighting projects, we also wanted something slim enough to slip into any design. It still uses an ESP32 for the best support, with USB-serial programming, 5A fuse, 5V level shifting + 100 ohm series resistors for pixel drivers, user/reset buttons, a user LED and onboard neopixel, JST SH analog/digital connector, QT I2C connector, 4 GPIO plus power/ground breakouts, and USB type C power/data input.

However, this version is made simpler and less expensive by dropping the DC jack and USB PD support: it's only for 5V strips if you want to power them directly (you could still drive 12V or 24V pixels, but you'll need separate power for them). Instead of a full set of terminal blocks for 3 signals, we only have two outputs, and they have to share the power and ground pins. It could also be used for a single two-pin dotstar LED setup. We kept the built-in I2S mic but dropped the on-board IR sensor - if you want an IR sensor, you'll be able to plug it into the JST SH port with a simple cable or solder it into the breakout pads.

The trade-off is that it's much smaller and slimmer, especially when no terminal blocks are soldered in by default: only 1.2" long x 0.785" wide (~1 sq in) x 0.3" thick vs. the original's 2" x 1.3" (2.6 sq in) x 0.55". To get it that small, we went 4-layer to give us a nice big ground and 5V plane in the middle and double-sided assembly. Coming soon.

[adafruit]

WLED to xLights exploration ✨🎆

Playing with our new Sparkle Motion board that's coming soon

Adafruit Sparkle Motion - All-In-One WLED and xLights Board

Coming soon! We're designing a board for using WLED - and we want to make like the bestest board in the wholeworld. Our resident me

we wanted to try driving a large display of LEDs and discovered that once you want to do custom display graphics, WLED is not super great. Instead, you can use the open source and free xLights software

which is completely amazing and has a learning curve like a cliff for the first 30 minutes. BUT once you get your controller and layout, it's unbelievably powerful and actually kinda easy to get going with simple display work. It also has a very satisfying preview mode.

[jonaled]

 The Novastar VX600 all in one controller. A perfect partner for your LED screen can manage up to 3.9 million pixels. For queries, contact Jona LED [email protected] www.jonaled.com

[jonaled]

Visit the Palm Expo 2022 to checkout the MX40 and other range of Video Controllers by Novastar. Witness the Complete range of LED Display and Controllers by Jona LED & Novastar Exclusively at Palm Expo

Booth No. D 45 26 - 28 May 2022 Bombay Exhibition Centre, Goregaon(E), Mumbai, India

www.jonaled.com

[jonaled]

Synchronization mechanism for multi-screen playing Powerful Processing Capability Omnidirectional Control Plan Synchronous and Asynchronous Dual-Mode Wi-Fi AP Connection

TB40

Synchronization mechanism for multi-screen playing

Powerful Processing Capability

Omnidirectional Control Plan

Synchronous and Asynchronous Dual-Mode

Wi-Fi AP Connection

[evledev]

RGB LED Controller Manufacturer

RGB LED Controller Manufacturer One Smart Lighting specializes in intelligent lighting control and smart home technology. The major products we produce is smart products which are divided into Smart LED controller, clever illumination as well as wise plug classifications, consisting of LED controller, RGB controller, wifi controller.

[facadeledlighting]

MADRIX 5 @ BLESS NIGHT CLUB in Marbella Malaga, Spain