#plushie tutorial

[hazy-egg]

ALRIGHT EVERYONE DAVE IS REAL AND IN MY HOUSE!

I had some vague interest from people wanting to know how to aquire one of these fuckers, so I’ve made a (slightly jank) tutorial on how to make one of these yourself! (instructions and materials below)

Materials are mostly self explanatory, but the chalk is for drawing the pattern on the felt, the glue gun is for attatching the mouth, eyes, and security badge to the plush, and the wire is to go through the body/neck/head so his head isn’t floppy. ALSO you’ll need scissors to cut the felt out (forgot to draw that lmao)

This is the pattern to draw out on our lighter felt for the head and body! This is specifically for Dave, but if you’re making Jack you can adjust the proportions on the body to be a bit shorter and wider. These are in centimeters because I am not American.

Cut along these lines, you can cut out each panel but I’m lazy so this works just fine.

You’re kinda turning these into cubes, think of it like one of those paper maps you probably made in elementary math class. Fold along the lines and use a whip stitch to attatch the pieces together AS WELL as stitch along the chalk lines-- that will make it look like you actually cut all the panels out and define the different sides. 

should start to look like this! Make sure to leave one side open so you can flip it inside out!

Once it’s inside out, you can stuff it and use a ladder stitch to close the last side. I reccommend leaving a shorter side open so the ugly stitch is less noticable. 

Once you’ve cut out the mouth, eye, and badge shapes you can glue them on!

Here’s where it gets. a little jank so buckle up!

This is the general pattern for the arms, legs, and neck. You’ll have to futz and adjust it... a bit because I am not stellar at making patterns, but this is good to get ya going!

This time cut out each panel

Also to note- If you’re making Jack you do not nead that much neck lmao

OKAY sO for stitching, this time it’s less straightforward. For the legs I folded each rectangle in half (Ugly side out!) and just stitched along the edge to make a tube

Kinda like this

Then flip it inside out, stuff, and fold and crease it to look like a foot using a whip stitch. To extra secure it I did a ladder stitch along the top to keep the foot upright

Then just pull the thread tight and boom you got a leg. Repeat that on the other leg and now he can walk.

Attatch it to the ass with a ladder stitch (and also secure it along the top with another ladder stitch to keep him in a sitting position if you want)

Now for the arms

So this is probably the most jank part of the tutorial. For the arms I ended up adjusting the pattern I had cut out to look more like this.

Then you just kinda

fold and pin it to get a boot-like shape. Use the extra fabric you cut off the bottom of the arm to make a little oval for the palm and then stitch it all together (leaving the top open). Then flip, stuff, and attatch with a ladder stitch!

mans kinda built like an Ugg boot. 

Lastly the neck is literally just a tube. If it’s Dave make it long. Just stitch along one side and leave the two ends open so you can put the stuffing and wire inside. Now for the Wire! To make sure it can’t puncture through the felt, bend the ends to look like this

Now to run it through him just take some scissors and snip two lil holes, one at the bottom of his head and one in the middle of the top panel of his body and have the wire go through his body, neck, and into his head. that’ll make his neck bendable. Then just attatch the neck with a ladder stitch and you have your man! For Dave just bend the neck into the desired potition aaand you’re done!

And if you follow the steps carefully you should end up with this mother fucker in your house!

[tumbleosity]

Tush tag tutorial for a friend! 

Notes: 

Your tag will not be water proof however depending on the quality of your printer they may hold up well in water. I tried to waterproof my tags with a sealant and it made the ink bleed terribly!

You can try and iron out the wrinkles if they bother you but in my experience it didn’t do much :/

If your tag is not a loop and is the simple rectangle version sew along one outer edge and the top edge and then flip.

[kinzplush-archive]

my tutorial on how to clean and restuff a build a bear at home !!!

1. find the seam on the back and use a seam ripper or scissors to cut it.

depending on your bear’s fur, it might be difficult to find. for example, when i restored my cuddly lamb bear, the fur made it a bit hard to find the back seam. my tip is to pinch both sides of the bear’s back with your fingers and separate until you see the seam, then use your seam ripper or scissors to cut it open! :D

2. unstuff your bear completely – or, almost completely.

get a plastic bag ready, and start to remove the stuffing!! depending on how old your bear is, and how much they were cuddled with, the stuffing might be pretty gross. also, it’s okay if you can’t get some of the harder-to-reach places, like the snout, paws, etc – it’ll air dry just fine!!! make sure to take out any scents or sounds before you move on to the next step.

3. wash your bear!!

a washing machine will work just fine!! just make sure it’s on cold :> if you’re worried about their fur getting damaged, you can put your unstuffed bear in a tied pillow case, but i’ve never had a bear’s fur damaged in my washer without one. i also just use my regular laundry detergent!

4. air dry your bear!

please please please do NOT put your bear in the dryer !!! the heat can damage their fur; air dry them instead!! i also like to use my (cooling) stand-up fan to speed up the drying process. it usually takes about 2 hours for my bears to dry completely!! :-D

5. restuff your bear!!

i use poly-fil for this!!! i recommend either this one or this one. the first poly-fil is softer and more similar to build a bear’s stuffing, and the second poly-fil is more firm. i also recommend having a chopstick nearby to help push the stuffing in !! :D also make sure to add back any sounds or scents previously in your bear.

6. finish your bear with a hidden ladder stitch!!

i’m not gonna teach this stitch, as i’m not very good at sewing, but this is the video i used, and i highly recommend it !!!!! this is my handsome man after the 5th time i did this stitch. :>

and that’s it!!! i’m super proud of you for washing and cleaning your plushies. it can be scary, i know!!! please dm me if u have any questions abt this, i’ve washed and stuffed build a bears 5 times, and i’m about to do it again on monday/tuesday (5/31 or 6/1) !!!

[squid--inc--writes]

Im going to make the little squid key chains tutorial undercut, but i made one. This is very much a "to your own preference" thing, very easy to customize, and, infact, encouraged. It's also gonna be a terrible tutorial because im bad at explaining thing. Lots of pictures. I use felt, so it will likely react differently than other fabric. Also, if you make one, either reblog this with yours, or tag (@squid--inc ) in your creating it, cause i wanna see!

@nekoazumie @wettthepottterheadss4120 @takottai

If you want to be tagged, untagged, or tagged in specific content, let me know. Reblogs help other people see my shit, and that is greatly appreciated.

Step one, cut out the base of it; head and sheet for tentacles (the reason the tentacle sheet is so large is that it gets braided, which makes it shrink)

The head and tentacles can be done in various orders, the tentacles i do are a basic 3 strand braid, this one has long thin ones, altho previous ones ive done have thick braids:

I used red lines as guides, where to sew the head, you will turn it inside out after

For eyes, i use those little glass pellets you get to decorate vases and shit, then paint the back with acrylic. (Let it dry completely, i use fabric glue to get them to stay properly, pressing down for 10-20 seconds, and leaving to completely dry. Shake test it)

Place the eyes where you plan on putting them, and trace a line around them, it's not necessary, but helps keep track of placement. You will want to keep them in place while sewing to keep the shape of the eyelids right. I can clarify if anyone asks, and you can't figure out how from pictures.

Once sewn on, cut off excess, unless you want to turn it into a detail

Take the tentacle piece (i used a different wip as an example because I'm tired and attach it to the inside of the squid ( hand sewing it works well)

Once those are attached, you can either leave the underside like that, or fill it with what you like, and attach an underpiece to it (i use scraps from the work itself, you can use anything, including scented stuff)

Attaching the key chain part, i took the end of the chain and folded fabric around it, and sew it in place. Then adding the attachment piece is up to you. I also use fabric markers to put patterns on them.

If you want to add a zipper, this can easily become a coin purse, you can make them larger, and use nicer stuffing for a stuffed animal to cuddle, there is all sorts of stuff you can do with it. :-)

[makeshiftwings30]

new plush making tutorial! how to joint limbs.

[dasabucket]

How to make an lil among us plushie!

Materials I used were a sock,cotton balls/stuffing,and felt!

If you want to make one! I highly suggest to use a stretchy kind of socks and if you want to use glue for the oval felt thingy,dont use Elmer's fabric glue! its shitty

[whiteantcrawls]

Interfacing and Minky: A Smol Tutorial

One of the issues plushie makers may have, when working with Minky is that it is a knit material and has some significant stretch to it along the cross grain--the grain that runs from selvage to selvage. The lengthwise grain--from cut end to cut end as it comes off the bolt--it pretty stable, with little stretch. Stretch can be good, when you are needing a rounded, firmly stuffed shape, because you can pack in the polyfil tightly and shape as you go. BUT stretch can also cause distortion, or make a leg or arm lengthen and get skinnier than you want. Stretch can make curved areas larger than you want as you sew, distorting the seamline since curves stray into the bias. 

Another issue with Minky as a knit is that it has a very soft drape. In other words, it can be a bit floppy. Again, this can be a good thing, if you want a soft roll on a mane/hair, or if you need to layer two Minky pieces over each other for clothes. BUT if you want some pieces to stand up, such as ears, spikes, or small wings, and you don’t want to wire them, you need to do something to firm up the floppiness and tame the drape.

Enter interfacing. Interfacing is a backing material that comes in lots of types, can be fusible or sew in, and have varying firmnesses. It can be used to control stretch, to add body and firmness, and to help with building structure into a plush.

I typically use a lightweight fusible knit interfacing (Pellon EK 130, white Easy-Knit Fusible), since it has many of the same properties as Minky, and still keeps some drape and softness. It adds firmness without straying into a cardboard stiffness, and it’s relatively inexpensive.

I buy this by the bolt at Joanns Crafts when they have a good coupon or sale. It’s very sheer, as you can see here:

Because it’s a knit, it has some crossgrain stretch, just like Minky:

And the same relatively stable lengthwise grain, with little stetch:

Why is this important? Well, by fusing the interfacing crossgrain stretch at right angles to the Minky crossgrain stretch, you can largely eliminate the stretch, while also providing some stiffness to the pattern pieces. 

In this instance, I’m going to use the interfacing to control the stretch in a pair of ears, so I can place them on the rounded head exactly, and to provide some stiffness, so they’ll stand up without stuffing or being wired.

First thing to do is to determine and mark the stretch direction on the Minky pieces AND on the interfacing. I routinely mark stretch and nap directions on the back of my Minky, shown in the red circle below:

The downward arrow is the nap--the direction that is “smooth” in the Minky “fur”--and the double-headed arrow is the stretch direction. You can see that the base of these ears is very long and curved, so it’ll be prone to stretching when it’s sewn in, making it harder to have them equally spaced and equally sized.

Interfacing doesn’t have a nap, but it does have one side that is glue on it, and one side that doesn’t. You can usually tell by the feel of it. The glue side is typically rough, and the unglued side is smooth. Because you want the glue side against the BACK on the Minky, determine which side has the glue, lay it face down, and mark the stretch direction.

You want the stretch direction of the interfacing to run at right angles to the stretch direction on the Minky, so they cancel each other out, and make the Minky stable.

Here you can see a piece of interfacing layed over the back on the Minky piece. The Minky stretch is marked in red, and the interfacing stretch is marked in purple. They run at right angles to each other.

You can also (faintly?) see that I have traced the outline of the Minky piece out. Cut out the interfacing to the outline of the Minky. Next stop is the ironing board.

Set your iron for whatever setting the interfacing directions recommend. Knit is usually fused with steam, so use the highest steam setting and set for the temperature recommended. 

Now some people will tell you that you can’t iron Minky on a high heat and a steam setting. You absolutely can, BUT you shouldn’t iron directly on the fabric. Minky is made from polyester and can melt, flattening the fluffy surface, if you iron directly on it. You’re going to need a pressing cloth, to act as a buffer between the iron and the fabric. I use a large piece of silk organza, because it’s sheer, so I can see what I’m working on, and it’s strong. 

I double this over, put the Minky fluffy side down, so the interfacing is on top, and place the pressing cloth on top of the Minky/interfacing sandwich. Now PRESS. Don’t iron--PRESS, with an up and down motion, using short bursts of steam with each position of the iron. You do NOT want to slide the iron in a typical back-and-forth motion, since this can cause the interfacing to slip out of position. Here you can see the curved edges of the iron sole plate where I have pressed down on the fabric.

Overlap the iron placement a bit, so that you cover the entire surface of the piece, paying particular attention to the edges to ensure a good bond. Use lots of steam, but not a huge amount of pressure. Once you have gone over the entire surface of the piece, set it aside to cool completely. This is a critical but often overlooked part of the process. The glue needs time to set as it cools. If you move the piece around, or start cutting it before it cools, you may not get a good bond, and the interfacing can peel off. So let the piece cool completely before you start cutting it.

Here’s the results of interfacing the ears:

Not only was it easy to position them exactly and stitch them in place without the edges of the base stretching out, but they now stand up nicely and cleanly, the tips are clean and sharp and they didn’t need to be stuffed or wired.

[sakura-snuggle-blog]

Kwl koala