Aug 17, 2015
Comment: ckessoun said "#Diesel jean #WoodMax tshirt #DIKKKKKo shoes @ckessoun fop"
seen from Austria
seen from United Kingdom
seen from Russia
seen from United Kingdom
seen from Yemen
seen from Sweden
seen from United States
seen from Netherlands
seen from Singapore
seen from China
seen from United States
seen from Malaysia
seen from United States
seen from China
seen from United States
seen from South Korea
seen from China
seen from United States
seen from China
seen from China
Comment: ckessoun said "#Diesel jean #WoodMax tshirt #DIKKKKKo shoes @ckessoun fop"
Configuring and Uploading Marlin Frimware
Configuring and Uploading Marlin Frimware
Marlin is an open source software which understands GCode and controls the 3D Printer hardware. Marlin will run inside Arduino Mega 2560.
Arduino IDE
You will need to download and install the Arduino IDE to compile and upload the Marlin firmware.
Download marlin firmware from http://arduino.cc/en/main/software
For step-by-step instructions on setting up the Arduino software and connecting it to…
View On WordPress
Preparing Printbed for 3D Printing WoodMAX (Prusa i3)
Preparing Printbed for 3D Printing WoodMAX (Prusa i3)
The Heatbeds are not perfectly flat, so you will need a glass that you can put on top of Heat bed. For WoodMAX i3 and Prusa i3 use glass in size of 3 mm thick 21cm x 22 cm.
You can use kapton tape or binder clips to mount the glass on top of heat bed.
Here is how you can easily install the Kapton tape on glass.
View On WordPress
WoodMAXi3 Electronics Assembly and Wiring
WoodMAXi3 Electronics Assembly and Wiring
Follow this guide to assemble electronics for WoodMAX i3 Kit
Mount the heat sink with the heatsink sticker as show in the picture
Electronics Parts
Assemble the RAMPS board on top of Mega 2560
Mega + RAMPS + StepStick After assembly
Zip tie the Electronics board in the side panel of WoodMAX i3, Warning: do not over tight, it will cause cracks in the PCB tracks
Power Supply Wiring Warning:…
View On WordPress
WoodMAX i3 Extrudre and X-Axis Assembly Guide
WoodMAX i3 Extrudre and X-Axis Assembly Guide
Follow this guide to assemble extruder and X axis of WoodMAX i3
aSensar All Metal Extruder Parts
Extruder Idler Assembly
Assemble the the gear in the motor shaft, the gears curling should align with the filament holes in the extruder as shown in picture
Mount the hotend in the extruder
Zip tie the LM8UU bearing and connect two M4 bolts
Insert the two 8mm shat into Extruder carrier bearing
Zip tie…
View On WordPress
WoodMAX i3 Print Bed Assembly Guide
WoodMAX i3 Print Bed Assembly Guide
Follow this guide to assemble the print bed for WoodMAX i3 3D Printer.
Print bed carrier and parts
Assemble the X Axis belt mount
Zip tie the LM8UU bears, and insert the 8MM shafts
Zip tie the Y axis End stop
Y axis mount parts and Print bed Assembly
Assemble print bed carrier assembly and use 4 lock plates and lock the in position
Pass the belt through Y axis idler and motor pulley
Tie…
View On WordPress
WoodMAX i3 Main Frame Assembling
WoodMAX i3 Main Frame Assembling
Follow this guide to assemble the main frame
WoodMAX i3 main frame parts
Assemble the main frame parts
Assemble the Front and Back Plates
Z Motor mount parts
Assemble Z motor mount
Z motor mount after assembly
Top plate assembly
Y axis idler and motor mount assembly
Z and Y motors assembly
Y axis idler and motor assembly
View On WordPress
WoodMAX i3 Z Axis Assembly guide
WoodMAX i3 Z Axis Assembly guide
Follow this guide to assemble the Z axis
Assemble the M5 nut and tight them using two M3 nuts and bolts
Assemble the bearings using zip ties
Assembled X axis motor mount
Assembled X axis idler mount Assemble use two 625 bearings as highlighted
Insert the 8mm shaft through linear bearing and scree the M5 threaded rod via M5 nut as show in figure
Like wise do it for X axis idler side too
Use…
View On WordPress