Untitled

[jdcustomsusa]

Everyone go check out @czeromedia for his official review of the JDC Coil-on-Plug Ignition System for the Evo 4-9. Orders are flying in, so don’t wait. Order yours today!

[jdcustomsusa]

Vibrant 10ft Roll of Black Nylon Braided Flex Hose; AN Size: -8; Hose ID: 0.44";

For just $51.95 Part #: 11968 Description: 10ft Roll of Black Nylon Braided Flex Hose; AN Size: -8; Hose ID: 0.44"; Material: Synthetic Rubber/Nylon Warrant…

For just $51.95 Part #: 11968     Description: 10ft Roll of Black Nylon Braided Flex Hose; AN Size: -8; Hose ID: 0.44"; Material: Synthetic Rubber/Nylon Warranty: One Year Limited Warranty MSRP: $63.50 USD Notes: - E85 Friendly- Black Braided Nylon Cover- Lightweight and Durable- Suitable for use with Oil, Water, Fuel and Coolant- Capable of handling operating temperatures ranging from -40 deg F to 300 deg F and elevated operating pressure of 500psi.

[jdcustomsusa]

Vibrant Swivel Hose End Fitting, 45 Degree; Size: -6AN

For just $14.95 Part #: 21406 Description: Swivel Hose End Fitting, 45 Degree; Size: -6AN Material: Aluminum Warranty: One Year Limited Warranty MSRP: $18.7…

For just $14.95 Part #: 21406     Description: Swivel Hose End Fitting, 45 Degree; Size: -6AN Material: Aluminum Warranty: One Year Limited Warranty MSRP: $18.75 USD Notes: Part Specifications:-------------------Available in Anodized Black finish only.

[jdcustomsusa]

MITSUBISHI OEM MASTER GASKET SET (EVO X)

For just $388.82 Nobody wants to have to pull an engine because of an old seal or gasket. You can save time and money with a genuine Mitsubishi OEM full gasket …

For just $388.82 Nobody wants to have to pull an engine because of an old seal or gasket. You can save time and money with a genuine Mitsubishi OEM full gasket and seal kit for your 08+ Evolution X. These kits come complete with every gasket or seal that you could possibly need when doing any level of engine work including, head gaskets, valve cover gaskets, spark plug 0-rings, intake manifold gaskets and more. The full kit contains over 160 individual gaskets and seals. We strongly suggest this kit for any engine swaps, rebuilds, or upgrades.

[jdcustomsusa]

JM FAB TWIN SCROLL EXHAUST MANIFOLD | 2008-2012 MITSUBISHI EVO X (EVOX-EXMANI-00)

For just $973.99 Replace your restrictive OEM cast exhaust manifold with our high flowing tubular model. By far the best EVO 10 Twin Scroll manifold on the mark…

For just $973.99 Replace your restrictive OEM cast exhaust manifold with our high flowing tubular model. By far the best EVO 10 Twin Scroll manifold on the market today! Made from thick walled 304 stainless steel tubing, this manifold is an exact replacement for the stock unit and no other modifications are required. Features near equal length runners with multi-pass TIG welded joints. All flanges are CNC machined from 304 stainless steel and surfaced to ensure a leak free seal. The head flange 3D contoured to produce a smooth transition from the runner diameter to the port shape. The ports are gasket matched and smoothed to perfection for the best of flow!Power gains can be expected throughout the entire RPM band. Just by bolting this manifold on to a stock turbo you can see 25hp gains. Includes a SS heatshield for the cam sensor harness.

[jdcustomsusa]

KELFORD CAMS 8-TX272 CAMSHAFT (MITSUBISHI 4G63 EVO 8)

For just $653.50 Mitsubishi Camshaft: EVO 8 - Hydraulic Kelford Cams range of high quality camshafts for Mitsubishi EVO 8, ground on a masterless Toyoda CNC cam…

For just $653.50 Mitsubishi Camshaft: EVO 8 - Hydraulic Kelford Cams range of high quality camshafts for Mitsubishi EVO 8, ground on a masterless Toyoda CNC camshaft grinderThe Best 272 degree cam on the market. These cams are ideal for street or strip applications making 400HP or more. KCG63 Adjustable Cam Gears available. Valve Spring Kit: KVS63BTK /KVSBKDuration @ 0.1 mm Valve Lift: 272 Inlet/272 ExhaustDuration @ 0.1 mm Valve Lift: 226 Inlet/226 ExhaustValve Lift @ 1.73 Rocker Ratio: 11.00mm Inlet/11.00mm ExhaustCenterline @ Full Lift: 107 Inlet/113 ExhaustValve Lift @ TDC: 1.52mm Inlet/1.00mm Exhaust

[jdcustomsusa]

RADIUM HIGH FLOW FUEL FILTER - 10 MICRON FINE STAINLESS CLOTH (20-0220-03)

For just $123.45 10 Micron Fine Stainless Cloth High Flow Fuel Filter by Radium Engineering The Radium Engineering high flow fuel filter has a 3 piece body …

For just $123.45 10 Micron Fine Stainless Cloth High Flow Fuel Filter by Radium Engineering The Radium Engineering high flow fuel filter has a 3 piece body that is CNC machined from 6061 aluminum and Type-II anodized for maximum corrosion resistance. Both removable end caps feature large -10AN ORB female threaded ports for high flow plumbing. The fuel filter comes preassembled with Viton O-ring seals for all fuel types including gasoline, diesel, methanol, ethanol, and alcohol blends such as E85. High fuel pressures < 150psi can safely be used with negligible pressure drop. The filter features a large 4.2"x1.75" element maximizing flow without sacrificing filtration. The filter element, made of Find Stainless Cloth, is re-usable (requires cleaning/maintenance), provides excellent filtration, and optimal compatibility with every fuel type. Several mounting options are available, but not required if you have your own mounts. Radium offers a standard single position mount, a dual-position mount (for use with 2 filters or filter and pump), and a Heat Exchanger mount with cooling fins which help dissipate heat. All of the mounts available are 60mm. Features High-Quality Fine, Stainless Cloth Element Excellent Filtration  Cleanable and Re-usable Optimal Compatibility with All Fuel Types Several Mounting Options Available Applications Universal What's In The Box? 1 - 10 Micron Fine Stainless Cloth Filter Element 1 - Filter Housing 1 - Mounting Option (if ordered) All Necessary Hardware Installation Instructions Warranty Information Instructions/Manuals Installation Guide Warranty All Radium Engineering brand products are subject to a 1 Year Limited Warranty from the date of original purchase. If a product fails, it will be repaired or replaced at Radium Engineering’s option when it has been determined by Radium Engineering to have failed due to defects in materials or workmanship.

[jdcustomsusa]

GSC POWER-DIVISION VITON VALVE STEM SEALS (MITSUBISHI 4G63)

For just $14.50 Details GSC Power-Division Viton Valve Stem Seals for the Mitsubishi 4G63T 6.6mm seal set (includes 8 intake and 8 Exhaust). These are an upgr…

For just $14.50 Details GSC Power-Division Viton Valve Stem Seals for the Mitsubishi 4G63T 6.6mm seal set (includes 8 intake and 8 Exhaust). These are an upgrade from the standard OEM material to help cope with the higher heat caused increasing the performance of your engine.

[jdcustomsusa]

MAP 2.5" LOWER INTERCOOLER PIPE | 2003-2007 MITSUBISHI EVO 8/9 (EVO-LIC)

For just $189.99 2.5" Lower Intercooler Pipe This MAP lower intercooler pipe features one piece mandrel bent 304 stainless steel tubing (Made in the USA) that …

For just $189.99 2.5" Lower Intercooler Pipe This MAP lower intercooler pipe features one piece mandrel bent 304 stainless steel tubing (Made in the USA) that has been bead rolled and routed with optimal flow characteristics in mind. This kit includes a 2.5" to 1.75" reducing elbow that yields the smoothest possible transition from the turbo outlet and matching T-bolt clamps so that you have everything needed for installation. Features One piece design 304 stainless steel Mandrel bent and designed for optimal flow Applications 2003-2007 Mitsubishi Evo 8/9 What's in the box? 1 Lower Intercooler Pipe 2.5 to 1.75 Coupler 2 Clamps Warranty MAP Limited Lifetime Warranty

[jdcustomsusa]

MANLEY VALVE SPRINGS AND TITANIUM RETAINERS | DSM / EVO MULTIPLE FITMENTS (26125)

For just $229.40 Manley Valve Springs:Manley Performance valve springs are specifically designed to withstand the rigors of today's aftermarket Sport Compact c…

For just $229.40 Manley Valve Springs:Manley Performance valve springs are specifically designed to withstand the rigors of today's aftermarket Sport Compact camshafts and properly control the valve train in these high revving Sport Compact engine applications. This means utilizing only the best, super clean chrome silicon high tensile strength steel alloy and performing classified heat treatment and shot peen processing to insure the ultimate fatigue life and limit load loss. Manley Titanium Retainers:Manley titanium retainers are manufactured in the very best dual spindle CNC machines to exacting tolerances rendering a superior jewel-like finish. We use rugged and certified, heat treated aerospace grade titanium bar stock. Retainer angles are held to within 6' (minutes) (this is a tenth of a degree) and installed heights are held to within .005" Titanium retainers are a must for your high RPM engine. Their lighter mass allows the tuner to turn higher engine speeds and still avoid dangerous valve float; without sacrificing reliability. Features Wound from super clean alloy Revs up to 10,000 RPM with Manley titanium retainers Designed to handle aftermarket camshafts Evo 8/9/DSM Valve Spring Specs O.D./I.D.: 1.100"/.775" Seat Pressure: 66 @ 1.580" Open Pressure: 175 @ 1.210" 237 @ 1.000" Stock/Max Lift: .370" .580" Coil Bind: .950" Rate (lbs./in.): 294 Evo 8/9/DSM Titanium Retainer Specs Valve Stem Diameter: 6.6mm Degree: 6° Dimensions A: 1.050" Dimensions B: .760" Step: .140" Height: Stock Applications 2003-2007 Mitsubishi Evo 8/9 1990-1999 Mitsubishi Eclipse/Talon/DSM 4G63 What's in the box? *Optional Spring & Retainer Kit *Optional Springs Only *Optional Retainer Only Warranty MFGR. Limited Warranty

[jdcustomsusa]

SKUNK2 RACING PRO-SERIES 68MM BILLET THROTTLE BODY (EVO 8/9)

For just $249.99 PRODUCT DETAILS The Skunk2 Racing Pro-Series Billet Throttle Body increases horsepower and torque by optimizing airflow to your engine. On …

For just $249.99 PRODUCT DETAILS The Skunk2 Racing Pro-Series Billet Throttle Body increases horsepower and torque by optimizing airflow to your engine. On forced induction applications, this quick bolt-on has shown gains of 50+HP. On high-output naturally aspirated engines, we have seen gains of 10+ hp. Skunk2's larger bore throttle bodies are capable of flowing enough air to support over 1000 hp. Skunk2 Pro-Series throttle bodies are precision CNC-machined from forged AL6061-T6 billet aluminum, vacuum tested, and hard anodized for increased durability. With greater reliability and smoother operation, Skunk2 throttle bodies exceed industry standards. Skunk2 has eliminated the factory water lines for cooler operation and each throttle body features a serialized Skunk2 nameplate to ensure authenticity.* High Flowing Large Bore Capable Of Supporting 1000 HP* Gains As High As 50+ HP On Forced Induction Applications* Durable and Corrosion Resistant Hard Anodized Finish* Uses Factory Throttle Cable* CNC Forged AL6061-T6 Billet Aluminum* Sealed Bearings For Smooth Operation* MAP Sensor Relocated To Bottom side For Cleaner Look* Eliminates Factory Waterlines For Cooler Operation

[jdcustomsusa]

MITSUBISHI OEM 75W-85 MANUAL TRANSMISSION FLUID (1 QUART) | MULTIPLE FITMENTS (MZ320197)

For just $11.50 Mitsubishi Motors MTF 75W-85 Genuine Transmission Fluid for the Evolution 8/9 6-Speed MR (DiaQueen), It is also recommended for the Evo 8/9/X 5…

For just $11.50 Mitsubishi Motors MTF 75W-85 Genuine Transmission Fluid for the Evolution 8/9 6-Speed MR (DiaQueen), It is also recommended for the Evo 8/9/X 5-Speed transmission, 1G & 2G DSM, 3000GT and Stealth. Please consult your owner's manual for the appropriate replacement schedule that's right for your Mitsubishi vehicle. PLEASE NOTE: This product can only be shipped within the Continental US and will only be shipped via GROUND service. Sold individually. Applications 19902999 1G / 2G DSM 19912999 Mitsubishi 3000GT / Dodge Stealth 2003-2006 Mitsubishi Lancer Evolution 8/9 2008-2015 Mitsubishi Lancer Evolution X Specifications Evolution 8/9: 3 Quarts Evolution X: 2.65 Quarts 19902994 1G DSM (AWD & FWD): 2.45 Quarts 19952999 2G DSM (FWD):  2.1 Quarts 19952999 2G DSM (AWD):  2.3 Quarts 3000GT & Stealth: 2.3 Quarts

[jdcustomsusa]

JDC EVO 8/9 Carbon Fiber Voltex Style Rear Exhaust Heatshield

For just $134.99 JDC Voltex Style Carbon Fiber Exhaust Heat Shield 2003-2006 Mitsubishi Lancer Evolution. Condition : Brand NewMaterial : Carbon FiberFits 2003…

For just $134.99 JDC Voltex Style Carbon Fiber Exhaust Heat Shield 2003-2006 Mitsubishi Lancer Evolution.  Condition : Brand NewMaterial : Carbon FiberFits 2003-2006 Evo 8/9 JDM Bumper Only - Perfect Fitment!Package Contents: One carbon fiber exhaust shield. Shipping time may vary depending on availability. Please message us or call [phone] if you have questions before ordering.

[jdcustomsusa]

AEM ADJUSTABLE CAM GEAR (EVO 8 / 9) 23-831BK

For just $123.19 AEM TRU-TIME Adjustable Cam Gears increase horsepower and torque without having to change the camshaft(s) and are must-have items for engines t…

For just $123.19 AEM TRU-TIME Adjustable Cam Gears increase horsepower and torque without having to change the camshaft(s) and are must-have items for engines that are milled, forced induction, high compression and/or utilizing aftermarket competition cams. Our gears enable users to match cam timing with their vehicle's tuning state by advancing or retarding the cam profile in one-degree increments via true laser-etched markings. Precision-cut gear teeth ensure no premature wearing of the belt surface and AEM's anodizing on the gear teeth is lab-test proven as the hardest anodizing process on the market. AEM TRU-TIME Adjustable Cam Gears are available in a multi-spoke, five-bolt design for most vehicles and our classic full-faced, three-bolt design for select applications. Five-bolt cam gears have an 8 in the suffix (23-8XX), and three-bolt cam gears have a 6 in the suffix (23-6XX). Increase horsepower and torque without any cam changes and are ideal for heavily modified engines Grade-8, six-point hex bolts stand up to repeated adjustments and feature an integral washer flange for greater load distribution True laser-etched markings on the leading edge of the gear allow for quick, accurate adjustments Hard anodizing on belt surface is lab-tested as the most durable anodizing on the market CNC-machined from 6061-T6 billet aluminum Comprehensive installation instructions, recommended cam gear settings and decals included Manufactured and assembled in the USA For Off-Road use only All AEM Tru-Time Adjustable Cam Gears are sold PER GEAR, so DOHC Motors will need 2.

[jdcustomsusa]

AEM DIGITAL OIL PRESSURE GAUGES 0-150 PSI | (30-4407)

For just $203.80 Digital Oil Pressure Gauges by AEM Electronics AEM Digital Oil Pressure Gauges combine unsurpassed accuracy, speed and control with an easy-to…

For just $203.80 Digital Oil Pressure Gauges by AEM Electronics AEM Digital Oil Pressure Gauges combine unsurpassed accuracy, speed and control with an easy-to-read digital LED interface that displays oil pressure in 1 PSI increments, and a sweeping LED "needle" that lines the edge and moves as oil pressure changes from 0 to 150. The oil pressure gauge's digital readout will automatically increase and decrease in intensity due to the built in ambient light sensing photocell. AEM's digital oil pressure gauges include a 0-5v analog output for use with data loggers and virtually any engine management system, such as the Infinity ECU, Series 2 EMS or AQ-1 Data Logger, making them the perfect solution for users who need to monitor and data log oil pressure at high RPM on tuned engines. Each gauge includes interchangeable silver and black bezels and black and white faceplates to personalize the look of your gauge. Features Easy-to-install Plug & Play harness and sensor included 150 PSIg Brass Sensor Reads 0 - 150 PSI 24 green LED display lights Auto-dimming gauge face and read out lighting Three digit readout in center Standard 52mm Gauge Housing 0-5V analog output Interchangeable black and silver bezels included Interchangeable black and white faceplates included Applications Universal What's In The Box? 1 - AEM Digital Oil Pressure Gauge 1 - AEM 150 PSIg Brass Sensor Extra Bezels/Faceplates All Necessary Hardware Installation Instructions Warranty Information Installation Instructions Click Here for Installation Notes Warranty AEM Electronics Limited Warranty

[jdcustomsusa]

MANLEY H-BEAM CONNECTING RODS 4G63 | 7 BOLT DSM / EVO (14022-4)

For just $377.94 Manley "H" Beam connecting rods are manufactured from 4340 forgings to the same exacting standards developed and approved by our original equi…

For just $377.94 Manley "H" Beam connecting rods are manufactured from 4340 forgings to the same exacting standards developed and approved by our original equipment customers. There is a vast difference in quality between a Manley "H" Beam and the "other" inexpensive H-Beams on the market. Weight matched to +/- 1.5 grams. Perfectly round big and small ends. Bend and twist is tightly controlled. Optionally we can apply an oil shedding thermal dispersant coating to your rods. This coating will speed up heat transfer from the rod to the oil then shed it quickly to allow fresh, cooler oil to come into contact with the rod. This will improve heat related stress issues associated with high performance, high revving, motors. A 'must have' for those wanting the highest confidence in their builds. Features Manufactured from 4340 forgings to the same exacting standards Heat treated, stress relieved, shot peened and 100% individually magnafluxed Perfectly round big and small ends. Benefits Bend and twist is tightly controlled Weight matched to +/- 1.5 grams Flywheel horsepower range for these rods in a 4 cylinder application is 600+ Applications 1993-1999 Mitsubishi Eclipse GST / GSX (7-bolt) 1993-1998 Eagle Talon Tsi (7-bolt) 2003-2006 Mitsubishi Evo 8 / 9 (7-bolt) What's in the box? Set of 4 Manley H-Beam Connecting Rods for 7-bolt 4G63 Cap fasteners are 3/8" ARP 2000

[jdcustomsusa]

RADIUM HIGH FLOW FUEL FILTER - 10 MICRON FINE STAINLESS CLOTH (20-0220-03)

For just $123.45 10 Micron Fine Stainless Cloth High Flow Fuel Filter by Radium Engineering The Radium Engineering high flow fuel filter has a 3 piece body tha…

For just $123.45 10 Micron Fine Stainless Cloth High Flow Fuel Filter by Radium Engineering The Radium Engineering high flow fuel filter has a 3 piece body that is CNC machined from 6061 aluminum and Type-II anodized for maximum corrosion resistance. Both removable end caps feature large -10AN ORB female threaded ports for high flow plumbing. The fuel filter comes preassembled with Viton O-ring seals for all fuel types including gasoline, diesel, methanol, ethanol, and alcohol blends such as E85. High fuel pressures < 150psi can safely be used with negligible pressure drop. The filter features a large 4.2"x1.75" element maximizing flow without sacrificing filtration. The filter element, made of Find Stainless Cloth, is re-usable (requires cleaning/maintenance), provides excellent filtration, and optimal compatibility with every fuel type. Several mounting options are available, but not required if you have your own mounts. Radium offers a standard single position mount, a dual-position mount (for use with 2 filters or filter and pump), and a Heat Exchanger mount with cooling fins which help dissipate heat. All of the mounts available are 60mm. Features High-Quality Fine, Stainless Cloth Element Excellent Filtration  Cleanable and Re-usable Optimal Compatibility with All Fuel Types Several Mounting Options Available Applications Universal What's In The Box? 1 - 10 Micron Fine Stainless Cloth Filter Element 1 - Filter Housing 1 - Mounting Option (if ordered) All Necessary Hardware Installation Instructions Warranty Information Instructions/Manuals Installation Guide Warranty All Radium Engineering brand products are subject to a 1 Year Limited Warranty from the date of original purchase. If a product fails, it will be repaired or replaced at Radium Engineering’s option when it has been determined by Radium Engineering to have failed due to defects in materials or workmanship.