Mitechpanelservices

      Mi Tech, a company based in Australia trades in wooden panel and lamination manufacturing machinery.     

[mitechpanelservices]

Wood Panelling or Wood Wall Panelling - A Comparison to Clear the Air

In case you are confused about the implementation of Wood panel technology in both wood panelling and wood wall panelling, here is a comparative study for you.

[mitechpanelservices]

Wood Panelling or Wood Wall Panelling - A Comparison to Clear the Air

Wood panelling and wood panelling are two areas of confusion that often creates problems because Wood panel technology plays a role in both of them. To address this area, we are here with a comprehensive blog comparing these two types from all aspects.

Wood Paneling

Wood panelling is a means of covering a wall that began in the seventies and eighties. It is used for the standard wallpaper and drywall painted or textured. Almost 4 by eight-foot sheets are also sold.

Functionalities

Wood panelling integrated with Wood panel technology on top of any material on the wall can also be used in new installations. This is because wooden panelling is extremely thin, usually less than 1⁄4 inch thick, and only needs a little adjustment if done correctly for the outlet and trim. This is a terrific technique to swiftly cover vast surfaces since each panel is quite large. Wood panelling is light enough to handle a person easily.

Size

In around 4 8 foot sheets all wood panelling comes. The beadboard and some types of wood panels usually consist of fine wood. They normally are between 3 and 7 ft in width and are 3/8 inch thick on average. For the finest quality veneer types, the standard plates of panelling could vary from 1/8 inch thickness to 3/8 inch.

Types 

Many wood panels created by Wood panel technology are identical and differ solely with respect to the wood kind and quality. Sustainable fan sheets are very thin and cover a wood sheet of inferior grade which is the basis. The use of paper skin on the low-quality foundation is also an alternative. Other versions are built of incredibly thin, sturdy wooden strips, usually approximately three to six feet wide. This band is fitted with the margins of the groove and the tongue. It's the most expensive type because it's solid wood instead of the splinter.

Wood Wall Panelling 

Wood wall panelling comes in a range of designs, species and can be painted or naturally finished in different ways. A great number of ways, grooves and tongues, ships, boards, battens, and batten, might also be employed on the wall. The wood wall panelling, the fruit of Wood panel technology can further fortify the structure to heavy winds and storms.

Functionalities

The wood wall panelling begins at the sawmill and is cured in wide drying ovens despite various materials and designs. From kilns, the wood-board is planned for all panels to the proper width and thickness. The board is then curved to fit the sort of panel, which may be placed on the wall throughout the sizing of breadth.

Size

Wood wall panelling integrated with Wood panel technology comes in different lengths and widths. As tight joints are allowed by a structure of grooves, the most common for tongue, groove and shipping is the random length. In most cases, the batten and board are 8 feet long, as they are often vertical on the wall. The tongue, groove and boat can be placed on either horizontal or vertical walls. 

Features 

Some species may be used in houses with pests, as several pieces of wood is insect resistant and can resist redness. The Cypress and the Easter Red Cedar are both types of wood that are resistant to redness and prevent the infestation of insects.

No matter whether you are opting for wood panels and wood wall panels, make sure the seller is well familiar with the integration of Wood panel technology. This will help you to get advanced end products.

[mitechpanelservices]

The Grade Comparison of Various Industrial Wood Panel Machinery

To let you understand the grade of equipment before you choose the right wood panel machinery, we have shed light on the comparison here. Check it out.

[mitechpanelservices]

Engineered Wood Floors - Is Wood Panel Technology Implemented Here?

Engineered wooden floors are also one example of the successful integration of wood panel technology. Want to know all about it? Here you go!

[mitechpanelservices]

Redefine Your Business Goals with Reliable Panel Lamination Manufacturers

If you want laminated products, make sure that you hire a professional company that is knowledgeable and experienced in panel lamination technology. Here is why you can’t skip this part.

[mitechpanelservices]

How Paper Impregnation Is Used For Durable And Attractive Laminates

A longstanding misunderstanding is that laminate is created from plastic. Nevertheless, a paper that is naturally derived and sourced sustainably is the key ingredient used to develop a lot of decorative laminates.

The process of making laminate involves kraft paper. This paper is the centre of the material that is made using paper impregnation technology. It is impregnated using resin and compactly pressed at intense temperature and pressure with a “décor” paper that is also impregnated with resin. The décor layer brings with it not only surface aesthetic and colour but it also fortifies it against heat, staining, impact, wear and more. Paper impregnation technology such as a press machine is used to bond the kraft paper permanently to the decorative papers thus creating a laminate sheet.

Different layers involved in laminate making

Softwood trees are used to gain alpha-cellulose wood fibers, which form the top layer, referred to as wear or overlay layer.  Lignin is taken out of the fibres and they go through a mild refinement process.  

The decorative layer is characterized by base papers and solid colours utilized to make print designs. Alpha cellulose is used for this as it prevents discolouration due to excess light and heat. The fibre used is mostly eucalyptus together with minor portions of hardwood and cotton.

In terms of the multiple layers of kraft paper, these are made from soft/hardwood. The wood, in this case, is sourced from recycled paper (like that which you find in grocery paper bags) and FSC controlled wood. There is no bleaching carried out for this paper. This layer offers the laminate the necessary impact resistance and fortification it needs.

Overview of the manufacturing process

In case you need to use laminate for bedroom cabinets or for large scale endeavours, for instance, restaurants, offices, schools, hospitals and so on, the process of manufacturing does not vary.

Paper impregnation

In the first place, the layer kraft paper that is basically the base of the final product is put through a roll via a paper impregnation technology-powered machine. The machine uses phenolic resin to impregnate the kraft paper. This is how the paper gets fortified and rigid. After the drying process, the paper is kept in storage to be used at a later time, during production.

In the meantime, the top paper, as well as the surface paper or overlay, get a melamine resin impregnation. This results in the durability and decorative fine-tuning of the laminate.

Pressing

With the help of a sizable press, the various layers of treated paper are organized by sections and put in between steel plates. At a temperature of 150°C and a pressure of 0.5-0.75 tons PSI, they are heated and compressed for a little more than an hour. After they are taken out and cooled down, they get cut appropriately and are subjected to thorough QC.

So, no matter what area you need laminates in, paper impregnation technology is equipped to give you superior quality laminates that suit all your needs.

[mitechpanelservices]

HPL - Why It Is Better Than Melamine

Melamine or melamine-faced is a prevalent word these days, as is melamine-coated to be used by paper impregnation suppliers. Even if these items are excellent in the wood panel industry, they pale in comparison to a well-made laminate panel of the same quality. Hence, what is the difference between these two? Unfortunately, many potential users are unaware. Buyers and users need to know what they are buying. Here are the distinctions, without getting too technical:

As the name suggests, Melamine is a low-pressure laminate and HPL is a high-pressure laminate Even though they may look similar, they are manufactured differently.

In order to create HPL, numerous layers of Kraft paper are impregnated with resin and then pressed together by the paper impregnation supplier. 1400 psi is used in its production, which is three times more than that of melamine. In order to produce a perfect bond, it is adhered to the substrate with a specific adhesive and then squeezed for 14 hours. When weight is a factor, MDF or poplar plywood are the most usually requested substrates. On birch plywood or other similar substrates, it can also be glued to chipboard.

Under a pressure of up to 500 psi, melamine, also known as "direct pressure laminate," is produced. Using melamine resin, layers of paper are saturated to produce a plastic surface through thermal fusion, giving the product its name. it's commonly glued or screwed to Chipboard or MDF at this point, forming MFC or MFMDF.

Advantages and Disadvantages

HPL laminated to a wood substrate is more durable than melamine because of the high-pressure process and has a stronger resin surface, making it more resistant to scratching, denting, and gouging. Standard, vertical, or post-forming grades are available. It is very resistant to water and chemicals. Shower panels made of HPL glued to poplar plywood are particularly popular because of their water-resistance. HPL offers an almost limitless range of colour and design options because the latest technology enables the use of decorative paper for your own design. You can use anything from your graphic designer to a company logo to a photograph and that’s why paper impregnation suppliers love it. 

You can't do that with melamine-faced items, which only come in a few colours and designs. You can see the difference between HPL and melamine in the woodgrains. It's not uncommon for the melamine to look false, but laminates like Lamicolor, ELS Autograph, ELS Artisan, Formica or Polyrey and others produce a remarkable likeness.

Why buying a melamine-faced product?

A full un-edged board can be purchased ready-manufactured by paper impregnation suppliers and utilised in locations with little traffic or dry circumstances, although it's most usually used because of its low price. If you want a finish that reflects favourably on your firm as one that does professional fit-outs or refurbishments, this is the way to go. It's always HPL.

[mitechpanelservices]

Tips to Choose The Most Suitable Laminate Sheets for Your Purposes

How to choose your laminate is often overlooked, whether you are an interior designer or a homeowner. To make a statement, we talk about wood panel machinery, combining patterns with solid colours, adding distinctive patterns and finding a balance between harsh industrial elements and warm colours and finishes.

Aside from the laminate itself, how you go about it is just as important!

Not only will choosing the wrong laminates takes away from the intended ambience of your home, but it'll also cost you more money in the long run if you decide to replace them.

Catalogues and online galleries provide us with a wealth of information on which to base our purchasing decisions. To be clear: none of these options gives us a complete picture of what it will look like when it comes to real life. If you want to compare your favourite laminates with the other laminates, you can do so in the catalogue, but it shouldn't be the deciding factor.

Here are a few reasons why you should choose a wood panel machinery supplier before finalising your laminate choice.

Full Pattern of Laminates 

When looking at the laminate chip catalogue, you can see and feel a little bit of its texture, but the sizes are far too small to appreciate and see the full pattern of the laminate that will be installed in your store or home. Look at the wood panel machinery to understand the pattern of laminates. However, while the actual sheet is 1.2 metres long, a laminate chip may only measure 6cm by 3cm. This allows you to see the patterns of the laminate up close, allowing you to make the best decision for your home.

The Right Color of Laminates 

However, don't let any online gallery be the sole factor in your decision-making process! This is due to the fact that monitors display the colours differently than the real product that is delivered to your home when it arrives.

Try to find out how a laminate sheet interacts with both natural and artificial light. As a result, you can decide where to install these laminates, whether it's in your living room under bright sunlight or in your bedroom under a soft amber glow.

Texture of the Laminates 

Wood panel machinery determines the texture of laminates. Even though browsing through a virtual gallery or catalogue could be convenient, it takes away from the entire sensory experience of running your hands through the sheet itself.

The texture and feel of laminates supplied by reputable companies are unique. The grain of the wood is synchronised with some corrugations, while others have a homogeneous corrugation from top to bottom.

Running your fingers through the laminate sheet in front of you is the best way for determining if it suits your design theme by feeling the texture of the entire sheet.

Try out the textures, patterns, and colours of the laminates under different lightings to get a feel for them. Take a look at the many ways laminates can be used. Contact a wood panel machinery supplier who can get you covered everything - from trendy ceiling art to intricately patterned walls for you to choose from.

[mitechpanelservices]

Types of Woods You Can’t-Miss to Learn About While Using Wood Panel Technology

If you are eager to use advanced machinery with wood panel technology, you must know the types of woods and their usages. Here you go!

[mitechpanelservices]

Benefits of Installing Laminated Furniture in Your Home

If you are thinking about installing laminated furniture in your home, make sure they are made by integrating panel lamination technology. Here is how you can get benefits from those.

[mitechpanelservices]

Why Installing Wall Panel Can be Profitable For You

Leveraging wood panel technology manufacturers create wall panels for your residential or commercial buildings. There are various benefits of getting those.

[mitechpanelservices]

Impregnating Paper to Create a Sustainable Building Material

Paper impregnation suppliers can offer the necessary machinery and technology to impregnate paper with a biopolymer and use it as a sustainable building material.

[mitechpanelservices]

Basic Wood Panel Machinery That You Must Need for Your Business

Wood panel machinery is a necessity if you manufacture furniture at home or want to start your own wood goods business. Equipment used in the woodworking industry to mould wood into the correct shape can range from A biscuit joiner, chainsaw, drill, nail gun, and wood squares etc. As the name suggests, they are used to join two pieces of wood together. 

The following are some examples of hand tools:

Wood Panel Machinery: It is mostly used to treat wood with a variety of tools. Many wood processing devices were used, and they were powered by electric motors.

Biscuit Joiner: Commonly used for joining two pieces of wood is the biscuit joiner or plate joiner. For semicircular cuts in wood composite panels, it has a blade with a diameter of 100 millimetres.

Chainsaw: This is a motorised, mechanical saw that may be carried about. Cutting and pruning are two of the most common logging activities. The chain saw is all you need for the tree variant. Common side effects include branch and leaf removal, and incapacity. It is common to use chainsaws to remove tree stumps and fallen twigs. To build three structures, therefore, it is necessary to cut saws.

Drilling Machine: Use a drill from the wood panel machinery to make holes in wood. When it comes to metalworking, woodworking and construction, drilling is a common practice. Cordless drill, hammer drill, and drill are three types of drills.

Jigsaw: All the baskets that contain the stencilled design on a little piece of wood can be made with a jigsaw. A jigsaw is a common tool in the toolkits of most carpenters. So, you've solved the riddle.

Nail gun: The nail gun is the ideal wood panel machinery for inserting wooden nails. The nails use electromagnetism, propane or butane, a highly combustible gas, and compressed air for power. Prior to this, nails were inserted into wood using hammers. Cut your fingers by using a hammer to strike them against a hard surface. Nail guns are used by many carpenters instead of hammers. For carpenters and builders, it's become a popular tool.

Wood Router: This is a huge piece of wood with an exit space. It has been superseded with a contemporary spindle tool. In typically, wood is shaped using an electric hand router, which has the same issue. A few paragraphs and grooves can also be cut using this tool.

Sander: A powerful wood panel machinery for achieving a smooth finish on the wood's surface. These Sanders are generally powered by electric motors.

Rotating tool: This tool is incredibly versatile and handy for any cut, carve, polish, etc. was done with the help of a number of spinning parts. As the rotary tool's torque is minimal, it is safe to use freehand.

No matter what wood panel machinery you need, you should always count on a reliable provider so that your investment doesn’t go in vain.

[mitechpanelservices]

Defining Aesthetics and Functional Needs Through Panel Lamination Technology Machines

Contact a leading manufacturer of machines based on panel lamination technology to manufacture laminates that captivates your customer’s attention.

[mitechpanelservices]

When looking around most building environments discerning observers will see engineered wood products everywhere

[mitechpanelservices]

High-Quality Paper Impregnation Technology to Improve Performance and Save Energy

Leading paper impregnation suppliers can offer you the right machine based on paper impregnation technology to help you produce impregnated paper.

[mitechpanelservices]

Engineered Flooring - Why Is This a Popular Choice?

For many families and home decorators, real wood floors are the preferred flooring option because they provide a warm and elegant aspect to any property that laminate and vinyl floors cannot beat. It is true that engineered wood floors made with wood panel machinery are gaining in popularity, but they are also becoming less expensive, making them a suitable option for every home. Eco-friendly in many circumstances, engineered wood flooring is a great investment for any home.

Benefits of Engineered Wood Floor

Layers of hardwood are glued and pressed together to create engineered wood flooring integrating the advanced wood panel machinery. Using a cross-grain construction, each layer is laid with great care, resulting in a product that is both sturdy as well as resistant to water and moisture. Traditional flooring procedures can lead to a lot of problems due to the wood bending over time. The distinctive properties of engineered have already led to an increase in the number of unusual designs, such as borders and scotia patterns.

As with engineered wood flooring made by incorporating wood panel machinery, there is a range of widths and thicknesses to pick from. As previously indicated, its ability to withstand moisture makes it an ideal flooring choice for a variety of spaces, such as kitchens and bathrooms. Engineered wood, on the other hand, is able to withstand a greater number of people walking on it, as well as extreme changes in temperature and moisture.

Engineered flooring can also be more practical in many circumstances because it is available in both pre-finished and finished forms, allowing the floor to be installed in just one step and be immediately functional. Additionally, with the right wood panel machinery engineered wood flooring is often only three-eighths to five-eighths of an inch thick, making installation a breeze. As a result, engineered wood flooring can be installed in a single day, eliminating the need for finishing, sanding, or tearing out the original floor.

Engineered wood flooring can be installed in a variety of ways, including floating or tongue and groove. Another consideration is the veneer of a flooring product because its density will determine how eye-catching it will be in the end.

Laminate Flooring 

Laminate floors which are also a product of wood panel machinery have a similar appearance to real wood floors but are less expensive and more durable. They may also be customized to create a real wood look at a fraction of the cost. To ensure a premium quality finish, leveling is essential because the laminate is not attached to the sub-floor. It's possible that laminate floors will feel bouncy if the sub-floor is bumpy. Because many laminates can be clicked together without glue, they can be quickly installed.

In spite of the name, solid wood floors consist of solid wood throughout. Solid wood floors are susceptible to scratches and dents, but this isn't a major problem in the long run because they can be sanded down several times.