http://simplepooltips.com

Advices, solutions and options Everything you need to make the perfect home swimming pool

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/choose-ground-pool/

New Post has been published on http://simplepooltips.com/choose-ground-pool/

How to choose an above ground pool

Lazing your days away near the water is no longer an out-of-reach luxury, but a reality that is available to almost everyone, especially with the advent of frame pools. These designs range from inexpensive and short-lived inflatable pools to durable, but more costly steel-framed ones. They are easy to assemble, and they can reach a length of 30ft, with 2 to 3ft depths, allowing you to comfortably swim and play. The range of above-ground pools is wide and choosing a good one is not as easy as it may seem at first glance. So, let’s go through what needs to be considered when buying, installing and operating one.

ADVANTAGES AND DISADVANTAGES

An above-ground pool is simply a frame and a polyvinyl chloride (PVC) liner. The frame can be of rods or panels, the interior is then covered with two layers of vinyl and one layer of polyester and attached to the frame. The pools are strong, and able to hold up to 50 tons of water, resulting in decent-sized pools for you and your family to enjoy.

Pros:

resistance to wear and tear

resistance to temperature extremes, frost and sunlight

decent service life (with proper care – about 10 years)

a wide variety of shapes and sizes

low price

relative ease of transportation and installation

most models can be moved from one place to another

Cons: the complexity of installing the pool and the possible need for additional equipment.

FRAME TYPE

Rod. Frames are made of vertical and horizontal supports. Vertical poles are threaded through special sleeves on a vinyl cover, with horizontal crossbars attached to them. The design is simple and quick to assemble, but is used for shallow pools.

Sectional or panel. The frame is assembled from metal or plastic modules, which are attached to each other by bolts or other mechanisms; inside, the PVC lining is laid out, and fixed with special fittings. These pools are strong, durable and easier to clean.

Seasonal and Frost-Resistant Surface Pools

Seasonal: designed for use only in the summer and should be disassembled in the fall. They are inexpensive, with lightweight frames. PVC lining will have to be replaced every season, since it’s not very thick material and is easily damaged by jumping, bumping and other active games. Moreover, the kits rarely include everything you need. Frost-resistant: with more durable reinforced frames and thick linings, they can tolerate prolonged exposure to low temperatures. Multi-season constructions are better when buried in the ground, but manufacturers say they will survive more than one winter above ground. The package includes almost everything needed to maintain the pool. Main advantages: high strength, no need to disassemble the structure before each winter and a lifespan up to 15 years. But you need to carefully choose a place to install the pool, because it is difficult to move.

METHOD OF INSTALLATION OF FRAME POOL

The first method is on compacted earth or poured concrete. This is best for smaller seasonal designs that are collapsible.

The second option is to install your pool in a specially dug trench. This option is only suitable for frost-resistant pools. Installation of such pools will require much more time, money and effort, but in the end you will get a full-fledged pool, the depth of which can reach 6-9ft deep. Such pools can be worked into any style of yard, allowing the sides and the territory adjacent to the pool to be decorated as you like. It makes for an ideal place to relax in the summer heat.

SIZE AND FORM OF OUTDOOR POOLS

Size is selected based on the area of the site and the number of people who will swim at one time. There are different variants on sale: length – from 9 to 30ft and more, width – from 3 to 15ft, depth – from 1ft to 6-9ft. The most popular frame shape is round, but there are oval, rectangular and asymmetric as well. The more complex the shape and the larger the size, the higher the price.

Compact pools with a depth of up to 5ft are suitable for small areas. Larger pools will look better in larger areas. If the pool is mainly intended for children, then a small inflatable option is suitable, since the extra depth will be unnecessary, and for a pool that will please the entire family, it is better to choose a spacious frame pool.

WHERE TO INSTALL THE POOL FRAME

Choosing the right place can add years to the life of your pool. It is better to place the pool near the water source and its drain. Additionally, it’s not recommended to put it the canopy of trees, as they are a source of shade and debris. Best of all is a flat area with a maximum gradient of 5 degrees.

INSTALLATION OF A FRAME POOL: MAIN STEPS

Preparation of the base. First, remove all stones, branches, and any hard, sharp objects, it is desirable to get completely rid of the grass and roots that can damage the pool during its operation. All-season versions can be partially or fully buried in the ground. To do this, you need to dig a pit, fill it with a layer of sand and gravel to a thickness of 6-8in and make a concrete pad of the same thickness. Professionals recommended strengthening the walls of the ditch with bricks.

Build the frame. Keep in mind the sheet frame for rectangular pools is assembled from separate parts, which are fixed with screws, and the joints are treated with sealant. When assembling the pool, vertical guides are placed in the pockets of the vinyl cover, then horizontal ones are installed, only then everything is connected. If there isn’t a concrete bottom, and the soil is loose, then put a wooden board or paving slabs under each support rod or leg. Connect the filter pump according to the instructions, all hoses and other necessary elements should be included. Do not turn the filter on without water in the pool. Most filters use cartridge and sand filters. Paper cartridges will have to be changed 2-3 times a week, and special quartz sand – once every 3-5 years

Install the ladder and fill the pool with water.

CARE FOR FRAME POOL: CLEANING AND “WINTERIZING”

The main thing you can do for the pool is to keep it clean. Without special filtering equipment, crystal clear water in a week will turn into a foul-smelling liquid, which can be dangerous swim in.

To filter the water, you need:

a filter pump, which eliminates dirt and other impurities in the water

a skimmer, to clean the surface of water from floating debris

nets and brushes for catching large debris and cleaning walls

chemicals are used to keep bacteria under control

Sometimes the filter pumps are equipped with a chlorine generator operating on ordinary table salt. In this case, additional cleaning is minimal and requires no more than the use of disinfectants. In all other cases, the use of special chemicals is indispensable. They are sold in sets which control the pH level and provide additional chlorine-containing components. To dissolve solids use a special float, which is often combined with a thermometer.

Preparing the pool for the winter:

seasonal constructions are disassembled, all elements are cleaned (pay special attention to the water lines), dried and stored for the winter in a place that stays above freezing. The instructions indicate how to store everything correctly long-term.

all-season constructions can also be disassembled, but more often they are left for the winter – the final decision is made according to the climate of the region. If in the cold season the temperature falls below -13 °F (-25 °C), then it is better to disassemble even all-season pools. Preparatory work begins at temperatures of 55-60 °F (13-15 °C). It is necessary to drain some of the water, leaving a little in the bottom so that the soil does not damage the structure. This is followed by cleaning the walls, chemically treatment the water, and washing and drying the equipment. Then cover the pool with a frost-resistant cover and wait for the next summer.

THE BEST FRAME POOL MANUFACTURERS

The name of the manufacturer is a guarantee of quality. Large companies give a guarantee, so it is better to choose their products. Minor savings when buying questionable products can turn out poorly, and you won’t be able to buy a new pool with what you saved if it does go bad.

Intex – the world leader in the production of inflatable and frame pools. The company was founded in 1964 in Los Angeles, today they have production sites located around the world. The range is huge, you can find models of different sizes, ranging in price and quality.

Bestway – is a Chinese company, with a considerable range of products. All of them are made of triple reinforced film, and the frame is reliably protected from corrosion. Prices are average.

UniPool – is a German company with a 40-year history. German quality has always been in the price, so UniPool pools will cost more than Intex or Bestway.

Atlantic Pool – pools from this Canadian company are now in demand in 90 countries around the world. All models are equipped with a sand filter (which are superior to the usual paper cartridges) and a skimmer, and almost all designs are cold-resistant.

Related Post

Swimming pool fencing ideas

How to build pool pump cover DIY

Best natural swimming pool designs

Vinyl pool liner installation instructions and vid...

.yuzo_related_post imgwidth:120px !important; height:110px !important; .yuzo_related_post .relatedthumbline-height:15px;background: !important;color:!important; .yuzo_related_post .relatedthumb:hoverbackground:#fcfcf4 !important; -webkit-transition: background 0.2s linear; -moz-transition: background 0.2s linear; -o-transition: background 0.2s linear; transition: background 0.2s linear;;color:!important; .yuzo_related_post .relatedthumb acolor:!important; .yuzo_related_post .relatedthumb a:hover color:!important;} .yuzo_related_post .relatedthumb:hover a color:!important; .yuzo_related_post .yuzo_text color:!important; .yuzo_related_post .relatedthumb:hover .yuzo_text color:!important; .yuzo_related_post .relatedthumb margin: 0px 0px 0px 0px; padding: 5px 5px 5px 5px; jQuery(document).ready(function( $ ) //jQuery('.yuzo_related_post').equalizer( overflow : 'relatedthumb' ); jQuery('.yuzo_related_post .yuzo_wraps').equalizer( columns : '> div' ); )

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/swimming-pool-pump-choosing-tips/

New Post has been published on http://simplepooltips.com/swimming-pool-pump-choosing-tips/

Swimming pool pump system choosing tips

Mounting a pool, do not forget that the flop in it like not only people. Here the perfect habitat for a variety of algae and microorganisms. Some insects also love aqueous medium. By the way, if the pool is outdoors, then hit him in the leaves and dust is inevitable. To get rid of these negative moments, and put swimming pool pumps are necessary. They help to clean, disinfect, and in some cases, to heat water. This article helps to gain an understanding in pool pump choosing topic.

Pool pump types

So, what are the pumps for its intended purpose? First – it is circulating pumps. They support the movement of large masses of water throughout the volume of the pool. Through them, and through the filter passes the main flow of water. It is called swimming pool pump and filter system.

If you have a large multi-purpose pool, it is possible to use pumps for Jacuzzi (bubble formation) in terms of the scenery – pumps for fountains and waterfalls. In order to disinfect water used small pumps with UV installation. This shows that there may be several, depending on the size, design and functional pool pumps. It all depends on your desires and capabilities.

In recent years, widespread so-called filter pumps for swimming pools. This is particularly evident from the manufacturers of frame pieces. The package already includes a ready filter pump for the pool. It is only necessary to mount for this scheme and change the filter cartridge in time.

At the expense of the filter elements – they are of two types: sand and cartridge. Sand pumps for swimming pools are used much more often than their counterparts cartridge. They are cheaper to operate, but the clean water from the solids only a certain size. Removable cartridges in this respect, better than sand. The size of the particles to be cleaned is very small.

Heat pump for swimming pools should be referred to a special group. It is a kind of multifunctional unit for your pond. He did not just stir and clean the water, but it will warm up to the correct temperature. Heat pump – a very promising investment.

Pool pump choosing tips

On average, per day triple pump should pump the volume of the reservoir. The higher the temperature of the water basin and operation rate, the more water must be “recycled”. Knowing the “cubic capacity” of its basin is easy to calculate the approximate capacity of the pump. Manufacturer always indicate how many cubic meters per hour circulates this model.

When selecting a pool pump system for the pool is necessary to pay attention to its noise characteristics. Too loud motor running is obviously annoying while swimming. It is also an important point.

It should be taken into account such as the technical aspects: location and method of installation of the pump, the water temperature and the ambient conditions, the desired voltage and secure the device connection.

The important role played by the manufacturer of the goods. The market is now a lot of well-known manufacturers that support the quality is excellent. Well-established company, take some money for his popular brand. But it normal. After the pump for the pool – a kind heart of the reservoir, on which depends the purity, beauty, and to some degree of water security. And it respectively affects the health and emotional mood.

How many water pool pumps needed

The number of swimming pool pumps depends on the design of the pool and its spaciousness. As a general rule, to inflatable and frame structures with large volume manufacturers are making one cup filter pump for the pool.

Stationary bowls that are used frequently, or year-round, require multiple pumps. The main unit is responsible for filtering, another – creates the counter, the third – UV launches the installation includes four fountains, etc. The more relaxation pool areas, such as jacuzzi, massage jets, the more pumps employ the work.

Swimming pool pumps features

Pumping equipment, in contrast to the filter is not removable device, so his choice should be approached with great responsibility. All pumps are categorized into:

self-priming

normal suction

filtering

All kinds of pumps in the basins often not used as an independent equipment, and in part filtering units, working as a unit with the filter. This is because the filter and pump are closely related parameters. Even buying a pump for the inflatable pool, you must pay attention to its performance that it is not higher than the performance of the filter. Otherwise, due to increased water flow rate recommended by the filter, purifying the quality deteriorates. Even worse, if such a discrepancy will damage the entire structure as a whole. You should choose the best pool pump suitable especially for your case.

Self-priming pump for swimming pool

It is the most common type of pool pump design used in swimming pools. He is able to raise the water to a height of about 3 meters, so it can be installed above the water level without using the check valve. However, despite this possibility, self-priming pump installed in this manner is not recommended because of overloading its service life may be significantly reduced. Best to place the device under the water level, for example, in the basement.

Normal suction pump

These pumps can not be set up without using the water level of the check valve. However, the ability of these devices are used for various types of special effects: whirlpool, waterfalls, fountains, counter. To install such swimming pool pumping system is necessary with special care to select the diameter of the pipe, and during its operation – to support the absorption of water from the pool without interruption.

The filter pump for swimming pool

pump for the pool filter is different from other similar devices by the fact that in its design provides a prefilter. This filter prefilter that traps large debris: branches, children’s toys, plastic bottles. This design increases the life of the pump, as it reduces the damage to the impeller.

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/maintain-pool-diving-board-diy/

New Post has been published on http://simplepooltips.com/maintain-pool-diving-board-diy/

How to maintain your pool diving board DIY

Diving boards are good for about 10 years, after that it will need restoration and will need to be protected from the elements. Diving boards are not cheap and that means that you are going to want to ensure that you are checking it and preserving it as long as possible.

Check the Diving Board’s Condition

When you have a diving board you are going to want to look at the rubber channels that allow it to bounce up and down. These also keep the parts of the board from rubbing together, you need to see that the boards do not rub together; if they are rubbing together you may be getting ready for a crack. You need to make sure that you are checking the underneath of your board to be sure that there is no cracking or rotting.

In addition to these items to check you will also want to look at the hinges on the board. If you are hearing squeaking when there is a person on it, you need to oil the hinges. You need to add some oil to them so that you can increase the timespan of all of the pieces. In addition to this, you want to make sure that you have an oil can that is on hand and you will need to oil it anytime you hear a squeak.

Another part of maintenance is cleaning your board, you will want to hose it off at least once a day. One time a month you also need to clean the board with chlorine or detergent to make sure that you are able to keep it clean as well as in great condition.

Monitor Your Diving Board Bolts

You need to make sure that you have a backup set of nuts and bolts so that you will have these on hand in the event there is a part lost. You also will want to see that none of your parts are rusted or loose. This means you will be able to keep your board safe and ensure that no one gets hurt.

You will want to make sure that all of your bolts are strong as well as that they are tight. You will need to have someone bounce on them on a regular basis as well to make sure that they continue to be in great condition. In the event that someone is not on it on a regular basis, it is all the more important to make sure that you look at it and use it regularly. You also will need to make sure that there is no rust that is showing up on the board.

Diving board replacement DIY

When you are ready to replace your diving board, you will need to follow these steps.

1. Order a new diving board. 2. Order back up parts and bolts. 3. Make sure you have all the hardware you need and secure it with a vice or a clamp before removing. 4. Remove the old board and the old bolts. 5. Apply the new board 6. Bolt it down soundly 7. Check the board for issues 8. Have someone test the board.

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/lets-choose-best-diving-board-swimming-pool/

New Post has been published on http://simplepooltips.com/lets-choose-best-diving-board-swimming-pool/

Let's choose the best diving board for your swimming pool

There are number of equipment that will enhance the swimming pool experience. Ladders, rail bars and diving boards are some of the key equipment. If you are intending to add more value to your pool, a diving board would be an ideal choice. There are certain facts that have to be taken into consideration when choosing a diving board for inground pools. This article will be of great support to you for choosing a perfect matching diving board for your inground pool. Follow the steps mentioned below to choose the most suitable diving board for your inground pool.

Step 1: Determine the dimensions of your pool

First you must measure the pool dimensions before considering the pool diving board. This will enable you to choose the diving board that will be identical for your pool. Especially give a great care to the deep end dimensions. After you measure the pool dimensions you will be able to choose the diving board using the diving board chart.

Step 2: Choose the Board type

When you know the perfect dimensions of the diving board, then you need to choose the type of board you are willing to install. There are two main choices when it comes to the pool diving boards. Jump board and the Dive board. It might sound odd, but there is a difference between these two boards. If you are willing to install a board that has a spring action, then you need to choose the jump board. Or else you can easily install the dive board which is just a board. The choice of brands and suppliers will depend on the choice of the board.

  Step 3: Compare the different branded choices

Choosing a board is easy but buying a board is tough. There are many choices in the market and you will be confused when you find them. You need to shortlist the brands based on the expert views. For an example SR Smith boards are ranked high in terms of bounce. Similarly you will be able to identify the quality of certain brands with the help of the experts. Another major fact that is required to be considered is the weight that can be held by the pool diving board. It will determine the longevity of the board as well. If you buy a board that has a low weight capacity and while using the board weight will be exceeded continuously, well durability of the board will be minimal. Therefore it is essential to make sure that you choose the pool diving board that has the highest durability.

If you consider the above mentioned steps while choosing the pool diving board, you will be able to choose the perfect match for your swimming pool. However you need to be careful when installing the pool board as well. Make sure that the board is installed in a place which has sufficient space for the pool users to move. Otherwise it will be a waste of money. Choose the ideal pool diving board for your pool and enjoy the swimming pool with your friends.

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/best-gas-heaters-swimming-pool/

New Post has been published on http://simplepooltips.com/best-gas-heaters-swimming-pool/

Best gas heaters for your swimming pool

If you are living in a cold area and there is a swimming pool in your garden, you won’t be able to resist the desire of swimming in it during the winter also. Yet you will not be able to bare the temperature. Desire is there but you can’t imply it into action due to the cold weather. The heaters used for swimming pools comes in handy during such situations. If your swimming pool is equipped with a heater you have the ability to heat up your swimming pool even in very low temperature situations. So no need to give extra money and travel to a hot water pool nearby. Just heat your pool and use it as a warm water pool.

There are several options to heat up your swimming pool during the winter. You can use a gas heating mechanism or else a natural air heating mechanism. However there are pros and cons in both situations. You can use from a variety of gas pool heaters for inground pools from the market. Choose the right size and capacity that matches the requirement of your swimming pool.

How does gas pool heater work

The other mot common mechanism is the gas heaters. Under this mechanism gas is burnt out to produce heat. This can either be natural gas or propane. Copper tubes placed inside a combustion chamber allow water to run through them. High heat of the chamber heats the water that runs through the tubes and ultimately your pool water will be heated. This mechanism allows the user to do it in a lesser cost compared to the electric resistance heater. However air pollution is a major concern of this process.

Different Types of Heaters Available

As mentioned before there are number of choices for your pool heater. Electric resistance heaters, gas heaters and solar heaters are the most commonly seen heating mechanisms used for the pool heating process.

Electric pool heaters

First type is the electric resistance heaters. These type of heaters use electricity as their energy source and heat up the resistors within the system. Then water washes out over the resistors and get heated. This mechanism is ideal for small pools as it requires a large amount of electricity. However this system has some key advantages over many other options. Since this operates independent from the air supply and has no air pollution this is used by any small pool and spa owners to heat pool water.

Solar heaters

Other most common type available in the market is solar heaters. A similar mechanism is used in this process. Instead of natural gases, propane or gas, solar energy is the energy source used for this process. This is one of the cheapest mechanisms available in the market. If you are willing to sacrifice a large capital for the installation, this mechanism is likely to bring bulk returns during the operations. But it requires some more knowledge to operate the system which makes it a tougher choice for the customer.

Best gas pool heater to use

Choice depends on your requirement. However gas heaters remain the most commonly used in the modern day due to its easy use and easy installation process. Especially it is the best choice when it comes to cost managing options.

Make sure to choose the ideal pool heater for your pool. Otherwise you will regret your choice later.

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/inground-ground-pool-heaters-can-use-swimming-pool/

New Post has been published on http://simplepooltips.com/inground-ground-pool-heaters-can-use-swimming-pool/

Inground and above ground pool heaters you can use for your swimming pool

There are many kinds of heaters that can be used for heating up water in a swimming pool. The most common used types are listed below with a small description.

Electric pool heater

Heat pumps are electrical heaters for pool. But they don’t act like a hot plate. Instead what they do is they extract and intensify the heat of the surrounding air and use that to heat the water in the pool. This kind of heaters are the most efficient heaters you can find in the market after the solar heaters. But unlikely the solar heaters heat pumps do not rely on the sun light. The working principles of a heat pump is quite similar to a refrigerator. The only difference is that the surrounding will be cooled and the extracted heat is the energy we use. The problem with the heat pumps is that, since the heat is extracted from the surrounding they are not very performing in colder states. And one unique thing about heat pumps is it can actually lower your pool water temperature too. So if the given temperature is 27C and water begins to heat up beyond that due to the temperature in the surrounding, then the heat pump will cool down your pool and maintain the temperature at 270 C. So it’s better to turn off the heat pump if you don’t need to heat up the pool.

Wood pool heaters

This is basically acting as a gas heater but the differences that the fuel is wood. This is much slower than a gas heater but faster than a heat pump or a solar heater. You need to burn considerable amount of wood to produce heat and the rate of heating is depending on the rate of burning. Unlikely the gas heaters these heaters are very simple in design and easy to use, yet the temperature is hard to keep at a steady rate. The efficiency is very low in this kind of heaters. But the running cost is very low. Perfect for suburban areas.

Solar pool heaters

These are the best efficient heaters you can find. There’s no running cost. It’s green and very low maintenance. But when installing a solar heater, we have to have some basic requirements. The first thing is the sun. Solar heaters are very good if you are living near equator. It’s not helpful for winter that much. Solar heaters are expensive too. And you have to have an enough sun facing roof space for the heating unit as well. Like the heat pumps, the solar heaters will take couple of hours to heat up the pool. There are two types you can find.

1. Coiled solar heaters – inexpensive solar heaters that can provide around 5 degrees of heat to a small pools.

2. Solar panel heaters – large scale heaters

Gas pool heaters

You can have gas heaters working with both natural gas and profane. The thing about gas heaters is that they are quick. You can start up a gas heater and the pool will be ready within an hour (depending on the size of the heater and the pool). And unlike heat pumps or solar heaters the gas heaters don’t rely on the weather. The market price for these heaters are very low comparing to heat pumps or solar heaters. But again the running cost of a gas heater is very high.

What swimming pool heater is the best

So as you can see there’s a lot to concern when it comes to choosing a heater. In most cases heat pumps are more popular than the other types of heaters. However, it’s very important to figure out what’s the size of heater is needed for your pool.

It’s based on couple of things,

1. What’s the size of pool 2. Whether salt water is used in the pool

There are some ways to save the water temperature in a pool so that when you need to heat up, you can have a head start. One way we can do this is using a solar blanket to save some heat over night time. This can save you about 8-12 degrees of heat of the water.

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/build-pool-pump-cover-diy/

New Post has been published on http://simplepooltips.com/build-pool-pump-cover-diy/

How to build pool pump cover DIY

Pool pump is an important equipment to keep your pool in proper operation. Therefore it is essential to keep it in a safe and protected method. Most of the pool pumps are above ground pool pumps. In some instances the pool pump is situated in a below ground building. In such circumstances an additional cover is not required. If your pool pump is located above ground an additional cover is a must. Especially since your pool is located in an open space a covered space or a building will not be available every time. Therefore make sure that you build a proper above ground pool pump cover.

Important rules for your pool pump cover

If you are building a pool pump cover yourself, there are certain things that you must be aware. It is necessary to follow these rules if you want to have an effective cover.

Make sure that the cover fits perfectly for your pump. If you have a large pump and you build a small cover, well it is not worth. Always make sure that cover provides adequate space for the pump

If you have the pump with you, first take the measures of the pump. This will allow you to determine the size of the pump cover. If you don’t have the pump and has already ordered or found the proper size pump, make sure to contact the supplier and get the measures of the pump.

Have proper cutouts for all the outlets. There are several outlets and inlets of the pump. If you are building up your own cover you have to take good care about them. If you don’t plan them at the start you will have to alter the design and change afterwards. So prepare the cover with all the cutouts for inlets and outlets in proper positions.

Choose a durable material which can bear up heat. If the material is not able to bear up heat it won’t last long. Also make sure that cover allows sufficient ventilation for the machine to cool down.

If you build up your own pool cover make sure that you do it in a proper manner. Otherwise your pump will get damaged as well as money and time spent to build up the cover will be useless.

All you should know about automatic pool pump cover

There are different types of automatic pool pump covers available in the market. All these are easy fitting covers. Just buy it, bring it and fix it. You won’t require any specific knowledge as there are manuals in these automatic pump covers. When you fix the automatic cover to the pump it will carry out the operations automatically. So if you are looking for a simple and quick solution for your pump cover, this is the best choice for you.

How to build pool pump cover – best ideas for your swimming pool pump

Your pool pump most certainly needs a proper protection method. So make sure that you either build up a proper pool pump cover or else buy an automatic pool pump. The best thing is to build your own pool pump cover at home. It will be cheaper and you will also enjoy your time building it up. Apart from that you will be able to build up a 100% matching pool pump cover with your knowledge and competency. Anyhow make sure that you have a proper cover for your pool pump to protect it for a longer period of time.

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/vacuum-pool-manually-instructions/

New Post has been published on http://simplepooltips.com/vacuum-pool-manually-instructions/

How to vacuum a pool manually instructions

It is essential to establish a cleaning routine for your swimming pool. If your swimming pool is not clean, it creates an unpleasant feeling for the users. Apart from that it will also reduce the life span of our pool. Therefore it is essential to establish a proper cleaning mechanism for your swimming pool. There are many tools that can be used to clean your pool. Some of the tools that can be used to clean your pool are listed down below.

• Pool skimmer • Pumice stone or tile brush • Pool wall brush • Vacuum head and hose or automatic pool cleaner • Telescopic pole

However it is essential to know how these tools can be used. In order to do that a competent person must be hired or else you need to improve your knowledge about pool cleaning process. There are automated systems as well as manual systems that can be used to clean your pool. Before looking at the automated systems let’s have a look at the manual system.

How to vacuum the swimming pool manually

In order to vacuum the pool manually you need to have a telescopic pole and a vacuum head. First of all you need to be careful that your vacuum is ideal for swimming pool cleaning purposes. If that is not done your vacuum will be damaged beyond repair and your work won’t be done. It is necessary to follow the steps mentioned below to clean your pool manually.

Step 1:

Attach the telescopic pole to the hose and to the vacuum head. Make sure that they are all fixed well. If not you will lose the vacuum head.

Step 2:

Slowly lower the vacuum head. Don’t be hurried. Make sure that you approach gently.

Step 3:

Continue to feed the hose into the pool until air is purged from the horse. You have to do this when it reaches the bottom. If you fail to do so and you connect the hose to your pump with air inside it, you are likely to burn out the swimming pool pump.

Step 4:

When you are sure that all the air has been removed from the hose, you have to pass the hose through the door of the skimmer and plug it to the vacuum port. This process should also be done carefully. Otherwise you are likely to damage your equipment.

Step 5:

Turn on the vacuum head and let the suction process begin.

Step 6:

You need to be double sure that the vacuum inlet is the only line open to the pump. If not particles and elements outside will also be sucked by the pump.

Step 7:

Remember how you vacuum our carpet? You have to vacuum your pool in the same way. Make sure to start from the shallow end and slowly move onto the deep end. You have to make sure that you use slow, long sweeping strokes for the cleaning process.

If you follow this process abruptly you will be able to get your pool cleaned well. It will also not damage your equipment as well. You have to rinse all the equipment using fresh water after each vacuum. So make sure that you rinse them well after each cleaning process. If not you will have to replace your equipment soon.

How to clean your pool using a skimmer

Skimmers are used by many pool owners to make sure that the pool stays clean. This is a very simple but effective technique. A skimmer pull water into the system through a skimming action from the pool. This also pulls all the debris and other items cleaning the pool surface. Skimmer basket catches the debris and the filtered water run through a pipe located at the bottom of the skimmer.

If you are having a concrete inground swimming pool, this is the best way to clean your pool. You can use the skimmer to vacuum the pool as well. Attach the vacuum to the skimmer and turn on the pump. This will increase the suction power of the skimmer and clean your pool even faster. However make sure that large debris are removed from the pool surface. Otherwise they will clog the pipes and ultimately damage your components. This method is ideal to vacuum your pool without losing water.

How to vacuum a swimming pool with a hose

If you don’t have a skimmer, don’t worry. You can clean your swimming pool using a hose as well. Connect the hose into the vacuum and lower it to the swimming pool carefully. Suction power of the vacuum will drag debris through the hose. Use long slow strokes over the water surface using the hose to make sure that you get all the parts of the pool surface clean.

How to vacuum your pool with a sand filter

Sand filters are the most commonly used to method to filter the swimming pools. You have to be careful when using the sand filter to vacuum your pool. First you must remove all the large debris from the surface of the pool. Use a net to catch them and make sure that there are no leaves or large particles of wood or plastic or any other material. Then connect your telescopic pole to the hose and connect it with your pump. Make sure to clean every part of the pool carefully. After cleaning the pool it is essential to backwash the sand filters. If you don’t back wash the sand filters filtering process won’t be effective. So make sure to turn off the pumps and start the back washing process. Always make sure that pool connection is shut during the process.

If you are planning to get your in ground pool cleaned, you can use the above mentioned techniques. While sand filter using process will create water losses, skimmers and manual vacuuming will let your clean your pool without losing water. Anyhow make sure to clean the pool daily to have a sanitary and more appealing pool.

How to vacuum a pool video

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/remove-scale-pool-tile/

New Post has been published on http://simplepooltips.com/remove-scale-pool-tile/

How to remove scale from pool tile

There’s nothing better than a summer day spent enjoying your backyard swimming pool. Keeping your swimming pool water clear is difficult enough, and can be the source of pride. Unfortunately without the right steps to prevent water line scale, it can build up over time and ruin your swimming experience.

Scale can be an unsightly blight on your beautiful pool tile that can build and damage your swimming pool equipment. There are several reasons that this can happen, either from poor pool circulation to excessive pH levels, but water line scale is public enemy number one for many pool owners. Once your swimming pool has this scale build-up, it can become very difficult to remove without the right procedures to prevent it. If you leave this scale untreated it can create pits or problems along the surface of your swimming pool surface, that can only be removed by having it resurfaced.

This can be a huge problem especially for people who have invested a lot in their inground swimming pool. Here are a few pointers on how to prevent and treat your swimming pool scale, especially when the summer months are just around the corner.

What causes scale buildup in pools

Calcium buildup is another term for swimming pool scale, and it can become a problem when you fail to maintain proper water balance. When your swimming pool water is out of balance or there’s excessive pH, calcium deposits can form along your water line.

Preventing scale build up in pools

When you want to keep your swimming pool looking at its best, check the water balance frequently to prevent scale. Calcium hardness over 1000 ppm is a definite warning sign, and pH over 7.8 can certainly contribute to the problem. When you are checking your swimming pool water balance, a high alkalinity reading of over 120 can also lead to scale forming along your swimming pool water lines.

How to remove calcium build up in swimming pool

When you want to learn how to remove calcium deposits from your pool, there are several treatments that can get the job done. There are many over the shelf calcium removers that can be used for both chlorinated and non-chlorinated pools.

Apply the chemical cleaner to the scale deposits on your swimming pool, and allow it to soak to make your job easier. Then use a wire scrubber or nylon brush to scrub the calcium deposits from the tile in your swimming pool. Especially tough scale can be removed using a razor blade. When you are removing your pool scale, make sure to remove the deposits and particles of calcium before they dissipate into the water. Keeping the scale from contaminating the other regions of your swimming pool and pool water is key to cleaning your scale and keeping your swimming pool in excellent condition.

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/clogged-pool-pump-problems-solutions/

New Post has been published on http://simplepooltips.com/clogged-pool-pump-problems-solutions/

Clogged pool pump problems and solutions

When your pool pump is clogged, there are several problems that can arise from the lack of circulation. Clogged piping can lead to premature pool pump failure and your water becoming unusable. Whether you own an in ground swimming pool or an above ground unit, you need to learn how to unclog your pool pump right away when you begin to see problems.

If you need to learn how to unclog pool pump there’s a few basic steps you can take to achieve this goal. This of course depends on what kind of swimming pool you own, and how your pool pump is setup. Although most clogging issues can be taken care of by any handyman or DIY’er, there can be several instances where a professional hand is required.

Clogged Pool Pump Problems

Some of the symptoms can range from noisy pump operation to backflowing pool pipes. Either way or water will become dirty and you will see an increase of debris. Some of the other issues around your clogged pool pump can lead to flooding issues or even worse. Many times your clogged pool pump can also cause noise and vibration as your pump struggles to operate.

These problems can arise when large debris gets stuck in your piping. It can also happen if you own an above ground pool and your pool pump pipes get pinched or bound up.

Pool Pump clogged with Leaves

If your backyard has trees that overhang your swimming pool, leaves can be a leading cause of clogged pool pump pipes. Because these leaves are often large and obtrusive, they can be the catalysts to your pipes becoming clogged and a lack of water flow to your pump and filter. To prevent this from happening make sure to check your skimmer frequently to ensure that nothing large gets sucked up into the pipes.

How to Clean a Clogged Pool Pump

The first order of business when you want to clear your pool pump pipes, is to turn off your swimming pump first. Once your pump is turned off, disconnect the pipes to the ingress and outlet ports of your swimming pool pump. If you are using a main union, make sure to disconnect that first to clear any large debris that may be stuck inside of it.

Using compressed air to clear sections of your pipe can certainly help you, although in most cases you must use an agitator to break up the clog. Something like a plumbing snake can really help get this done and this tool can be rented at your local hardware store. Clogged pool pump pipes can cause a lack of water flow to your pool pump, until your pump fails from lack of water flow. If you find your swimming pool water experiencing excessive drainage and water flow issues, use these tips to help you unclog your swimming pool pump pipes immediately.

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/repair-noisy-pool-pump/

New Post has been published on http://simplepooltips.com/repair-noisy-pool-pump/

How to repair noisy pool pump

Pool pumps are an important factor to your swimming pool maintenance, whether you own an above ground or inground unit. Swimming pool pumps are responsible for circulation of pool water through your filter. Because it’s a main component of your swimming pool cleaning system, it’s imperative you keep your pool pump in good condition and running optimally. Failure to do so can create an increased electric bill, prematurely clog your pool filter and dirty swimming pool water.

Your swimming pool pump motor will usually make some sort of noise during normal operation. While your pump emits noise as it operates, it’s usually not excessively loud or annoying. When the noise does become louder and continues to grow louder, it’s a sign of your pump going out. Swimming pool pump noise can eventually become so loud that it’s impossible to ignore and can make it impossible for you to use it.

Why your pool pump is making noise

If your pump is making more noise than usual, it’s a clear indication that your pump is beginning to fail. The beginning stages of pump failure are typically a pool pump making humming noise, or even excess vibration. When you fail to rectify the problem, these issues will only get progressively worse.

Failure of our pool pump can range in reasons, from clogging, dirty pool pump motor brushes or a failing pump motor. Because the internals of your swimming pool pump may be compromised, this causes the noisy operation. Typically this kind of noise can range from grinding or screeching, and can even become a loud screaming sound.

How to fix noisy pool pump

Usually swimming pool pumps aren’t meant to be serviced or taken apart, but there are things you can do to make sure you are doing what you can. Here are some of the steps you can take to fix your noisy swimming pool pump below.

Adjust the base of your swimming pool pump

When you see your pump wobbling or making noise from excessive vibration, it’s a sign of runout or your pool pump motor being misaligned. Try to tighten down your pump and securing it to prevent this kind of movement and noise.

Check your skimmer baskets

Large debris or floating objects can cause blockages which lead to dry conditions in your water pump. This can cause your pump to run hot or lead to premature swimming pool pump failure. Check your skimmer baskets and make sure that there’s nothing blocking the entryway of your swimming pool pump.

Clean pump internals

Because your swimming pool pump is basically an impeller driven motor, you can save your swimming pool pump by cleaning the interior. Always disconnect the power to your swimming pool pump before opening it and attempting to service anything.

Remove the strainer basket and filter from your water pump, and then use a wire coat hanger or similar thin metal pin to try and clear out the inlet and outlet ports.

If your attempts to clean or fix your swimming pool pump fail, seek out professional assistance or replace your swimming pool pump to restore proper operation.

[nedkampmann]

Swimming pool pump system choosing tips

Any type of pool whether it large monolithic or compact dismountable model requires special equipment making its operation friendly and safe. By binding devices the presence of which is necessary refer the swimming pool pumps. Their type and proper amount is determined and based on the purpose and scope of the pool. Read more: http://simplepooltips.com/swimming-pool-pump-system-choosing-tips/

[nedkampmann]

Beautiful Pool lighting design ideas

Any backyard landscape cannot be complete without a pool, in my humble opinion. You can cool off during hot day and have some fun during night. It is very important to lighten your pool due to the fact that people unfamiliar with your home can easily fall there. By installing swimming pool lighting you will provide safety and guide your youngsters and pets around a pool. Nowadays infinite lighting designs and landscaping ideas are presented, so pool can be illuminated not only for safety but for highlighting it`s true beauty. Read more: http://simplepooltips.com/swimming-pool-lighting-design/

[nedkampmann]

Astonishing swimming pools deck ideas

Building a pool deck can be tough, but it`s definitely worth the effort! By reading this article you can get the general information on above ground pool deck ideas, pool deck types, above ground pool deck plans, inground pool deck designs and a DIY guide. The main purpose of pool deck is to provide functional space for people to walk and sunbath. But no one said that your pool deck cannot look just fantastic! Firstly, you should decide what type your pool deck will be, consider all pros and cons according to your situation and only then start thinking about your deck design. Read more: http://simplepooltips.com/swimming-pool-deck-designs/

[nedkampmann]

Best pool design ideas guide

Many pool owners are used to consider swimming pools as place for restoration, as children playground during summer, as anything else but not as strong aesthetic element of an overall design.. Read more http://simplepooltips.com/swimming-pools-ideas/

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/vinyl-pool-liner-installation-instructions-video/

New Post has been published on http://simplepooltips.com/vinyl-pool-liner-installation-instructions-video/

Vinyl pool liner installation instructions and video

Pool liners come in all different kinds of shapes and materials, but one of the most common types is the vinyl pool liner. These liners are typically constructed of high impact vinyl and plastic composites. Vinyl pool liners are essential parts to your swimming pool maintenance, and they give your pool a layer of protection.

Vinyl Pool liners feature a bead at the outermost layer, which allows them to fit into the track along the bottom of your pool’s coping. This liner is placed over a sand, concrete or vermiculite layer and rise up to meet the pool walls, which are usually supported to prevent sagging or bowing. These walls make up the panels to your swimming pool and can vary in size and shape, which leads to the variety of vinyl swimming pool liners.

Whether you live in a warm or cold climate will dictate whether you need a pool liner, and if you are planning a new inground or above ground swimming pool, use our guide to determine your pool liner needs.

How to Install a Pool Liner

Whether you have an above ground pool or an in ground one, there are several steps that are universal to the installation of any vinyl pool liner. Pool liners come in different sizes and shapes, so it’s important to determine and measure your needs ahead of time. While the steps for an above ground pool will clearly differ from the in ground pool, you still must get the same job done.

1. Remove the vinyl liner and inspect for any defects. 2. Prepare for installation around your coping rail 3. Align liner and properly secure 4. Add water slowly to test

How to Install Above Ground Pool Liner

Above ground liners are much more easier to install, especially if you’ve just setup your pool framework. Once the above ground pool frame is in place, you are ready to install your liner. Although it can be a little difficult to install your own above ground liner, you can save a lot of money by doing it yourself. If you are dealing with a large above ground brand, it’s best to find the liner that’s cut and made specifically for your brand.

How to Install Inground Pool Liner

Inground swimming pool liners can be daunting to install, but with the proper research and measurements, it can be a rewarding project. Before installing or starting your project, you must get the right measurements for your inground pool. Measurements must match your liner and should be at least as long as the longest section of your pool.

If your inground swimming pool is a free form style, you must have a X and Y plot using two measures to properly size and cut your vinyl liner. Once you have the measurements ready, the next thing to do is to cut your liner and prepare it for installation.

1. Drain your inground swimming pool 2. Inspect walls and floor for damage or rust 3. Wash and broom the pool thoroughly 4. Tape the liner to the walls 5. Use a skimmer to eliminate bubbles and excess air from under the liner 6. Add water to your inground swimming pool carefully 7. Install your faceplates and water grates

Once you have installed your liner and cut holes and accommodations for your faceplates and gaskets, it’s time to finish filling your inground swimming pool.

Vinyl pool liner installation video

If you need help visualizing the installation of your inground swimming pool, you can use some of the many videos online to see how truly easy it is. When searching for videos, keep in mind that you should specify whether your swimming pool is an above ground unit, or an inground one.

How to Change a Pool Liner

Changing a pool liner can be difficult, especially if you have already set your tiles in your inground swimming pool. When you are in doubt or don’t know how to properly service your pool liner, you should always turn to a professional for real assistance. But if you have already installed your own liner, a replacement inground vinyl pool liner installation job won’t be very hard to do.

1. Drain your swimming pool completely 2. Cut your liner at the bottom of your inground swimming pool 3. Extend these cuts to the top of your track and cut along the base 4. Remove the skimmer faceplates and returns and take off all plastics 5. Remove the swimming pool liner

Once you have the old swimming pool liner out, you can move ahead and begin installation of your fresh liner.

[nedkampmann]

New Post has been published on Simple Pool Tips http://simplepooltips.com/install-solar-panels-heat-pool/

New Post has been published on http://simplepooltips.com/install-solar-panels-heat-pool/

How to install solar panels to heat a pool

Solar power and the benefits of using the sun to power are becoming increasingly popular to homeowners everywhere. One of the more uncommon ways to use solar energy is to heat youringround swimming pool. Eco-friendly and a great way to minimize your carbon footprint, using solar power to keep your pool water warm is a secret that many pool owners are using to their advantage. Before you consider using solar panels to warm your swimming pool, you should think about the many factors of solar energy.

When you are thinking about utilizing solar power to supplant your swimming pool heating system, make sure you have enough space to accommodate the panels first. Unlike traditional gas powered heating systems, you will need to keep your water pump running to properly heat the water in your pool. If these concerns are matters you have already considered, you may be surprised at how easy and beneficial installing solar panels can be for your pool.

Solar Energy Advantages

Using solar panels to keep your swimming pool warm may be a less popular method of using solar energy, but it doesn’t change the fact that it’s still very effective. Solar power is a free effective means to convert the sun’s rays to positive energy that you can use in your home. While the initial cost and investment of solar panels may seem counter-intuitive at first, it’s only a matter of time before the solar system pay for themselves.

The pool solar heater install may not be an easy undertaking, but with the proper planning you can utilize the sun to keep your swimming water pleasant and warm.

Pool Solar Heater Build

To integrate solar panels into your inground swimming pool, you will need a 3 way valve installed from your pump to your panels. These valves can be adjusted to route water to your solar panels in a regulated manner. Before installing your 3 way valve, you’ve got to install a proper tee fitting into your feed or return pipe. This tee allows your valve to operate and route pool water to your panels and back.

If you live in a cold weather area, it’s always a good idea to use a 3 way valve that can be opened to drain your system during the winter months. Installing a drain in your piping at the lowest point of your solar panel pool system is vital if you want to prevent freezing. If your solar panel swimming pool system lacks the right drainage system, plan on using pressurized air to keep water moving. This is one of the first steps to learning how to build a solar water heater for a swimming pool.

When installing your solar panel piping, use the same size piping to and from your 3 way valve to ensure even flow and even distribution. If you are using panels mounted on the roof, you need a strength rated union fitting that’s capable of handling the load. Even for ground mounted solar panels, the right union fittings make maintenance much easier.

Mounting your solar panels are the biggest challenge when it comes to your pool solar heater install. After your panels are properly mounted, you should consider using rigid piping to keep your pool an yard clean.

Once you have the piping routed around your panels correctly, the next step is to install the right solar controller system. Many of these units are computerized and can be vary in features and design. If you are looking for a comprehensive solution, many of these units can include temperature probes and variation valves to make maintenance of your swimming pool a breeze. Because this is the “brains’ of your pool solar heater install, make sure you get a turnkey solution that controls everything in one package.