#mhartstudio

[mhartstudio]

War Hammer 40k Chain sword

The idea is not new, but the point was to create a 3d model and make this sword with moving blades with electronics and batteries

[mhartstudio]

Getting started on the mask of Corey Taylor from the group slipknot

[mhartstudio]

Star Wars Clone Trooper Fives Helmet Ver.2 Clone Wars Cosplay https://www.etsy.com/listing/1074216733/star-wars-clone-trooper-fives-helmet?ref=shop_home_active_1&frs=1&cns=1

[mhartstudio]

Iron man War Machine mark 4 #mhartstudio #fusion360 #tutorial #3dmodel

I used to make a helmet like this a long time ago. But later I noticed that the previous helmet didn't have the same visor as in the movie and had completely different eyes and made it look like it was just a sad iron man. In this model, the eyes have been reshaped, the cheeks have been corrected and now the mechanical changes are being worked on!

[mhartstudio]

Billy doll masks from the movie "Saw"

This mask is created from the Pepakura file

This is a 3d model of a mask for printing on a 3d printer, and not a physical mask, pay attention to it! The mask is designed for the head of an adult! The temple width mask has 16.7 cm. The eyes on the mask are made separate so that after printing they are easier to process, paint and paste to the eye sockets inside. The mouth on the mask has mobility and is held by the connectors inside, which are closed with a special plate and screwed with screws with a diameter of 3 mm. There are also connectors for the nut for screws, after installing the nut in a special hole for it, it is stocked so that the screws do not fall out when spinning.

On the inside of the mask, you can fix the elastic so that the mouth returns to its original position, for this special holes are made for rubber! Instagram: https://www.instagram.com/y.s.maskcraft/ Etsy: https://www.etsy.com/shop/YSArtStudioCrafts

[mhartstudio]

Helmet Cyber sub-zero from the game of the mortal kombat 9 This helmet was modeled on the basis of a scan for Pepakura, which I found on the Internet! After modeling the main part, detail was added! When modeling, I tried to make some elements finishing so that after 3d printing it would be easier to process, load and paint, and then it would be possible to screw to the helmet! Electronics and backlight can be added at my discretion, I also thought through these moments and made end-to-end places on the ear antennas so that the wires could be stuck there! YouTube: https://www.youtube.com/watch?v=5s-QzYb0hO4&ab_channel=M.H.ArtStudio Instagram: https://www.instagram.com/y.s.maskcraft/ Etsy: https://www.etsy.com/shop/YSArtStudioCrafts

[mhartstudio]

Star Wars | Phase II Clone Trooper 3d model

Modeling this clone helmet from the second phase took a little more than 10 days. I saw most of the helmets of different masters and all of them were one whole helmet. In this helmet, I made a separate comb from above, individual ears, separate teeth and in front of the ducts. Why exactly? Firstly, this helmet will be created in the future into a physical object. Secondly, individual parts will be convenient in post-processing and painting. And thirdly, if you replace the ears, you can put an antenna, a sight or additional glasses there. This helmet acts as a designer! https://www.instagram.com/y.s.maskcraft/

[mhartstudio]

The Mandalorian Helmet is completed and available for order. The Mandalorian helmet is made of polyurethane plastic. The helmet is designed for the head of an adult. Inside the helmet, the distance from ear to ear is 18 cm, from the back of the head to the nose is 22 cm. Color helmet quartz 630. The visor in the helmet is made of transparent plastic and covered with a dark tinting film https://www.etsy.com/listing/1133573583/the-mandalorian-helmet-cosplay-helmet?ref=shop_home_active_1&frs=1