#bjd object head

[everydaydollydomes]

Steinberg had almost no issues during their test print...except apparently when I went through to update everyone's neck pegs I either missed theirs or didn't save it so it's a bit shallow on the two I did today -.- Not too bad a flaw all things considered, but they either need to be sueded or strung fairly tight for the head to hold a pose well. It'll be fixed when I make their file available later tonight or tomorrow.

[everydaydollydomes]

I finalized two heads today! Both have been in my WIP pile for a loooong time for a variety of reasons. We have the new Wavelength 2.0, which is very special because it really shows off how far I've come since I started modeling. Now, if you do get this one, there will be some minor differences between what you see in the picture and what's in the actual file - while I was removing the supports, a small portion of the antenna actually broke off and I realized it was just too delicate. So, I went back in and thickened it just a bit. You also can't see my shop name/signature on the back, which I try to include in some way or another on my doll heads so I did want to fix it. I did this by, well, making it bigger BUT I did also change it to just the initials so maybe it looks more like a TV brand than my shop name. I also thickened up the inner walls just a little cause I realized they're super thin. Unlike my first head, this one has a lot more space for pulling the string through and getting the screen in, which is magnetic! It uses a 20x4x1 rectangle magnet and it is STURDY. However, you can also just some sticky tack if you don't wanna spring for extra magnets.

We also got our GamePal Ultimate which is inspired by the Gameboy Advanced and I think was like...the second sculpt I started working on initially? Idk why it took so long to finish, I just got distracted by other stuff, I guess. Both are using 7x2mm magnets for their headcaps and can be found on both my Ko-fi and Cults3D which are on my pinned post.

Both heads will be coming with me to Resin Rose, though this particular Wavelength will likely be slightly discounted since it is technically a test print. I'll also have it in the slightly updated version in different colors.

[everydaydollydomes]

Brewnhilda has been printed!!!! Notes notes notes!! A little heavy with both the pot and cup BUT so long as the body was fairly well and tightly strung, it wasn't too much an issue and they still stood pretty well! I think I want to find a way to try and smooth it out a bit more? There's some left over artifacts so the curves are….not entirely 100% smooth. Sanding DOES help but it'd be nice to have less sanding be needed. My shop name didn't come out very well on the inside of the pot, especially with all the supports but I'm not sure how to clean up the embossing now that it's done….

The alt lid! Somehow the magnet wells came a bit small?? So I had to dremel them a bit and still couldn't quite them even, hence the gap depending on which direction you face the cup. Working on fixing that right now (turns out the same issue was on my wavelength screen so I'll have to fix that, too, if 3D builder will behave.)

Overall, I think Brewnhilda came out super cute!!! After a couple small tweaks, I think it'll be ready for sale!!

[everydaydollydomes]

Finally getting around to finalizing my Gamepal Ultimate (I just call it Pal for short). It's printed in Sunlu's taro purple and...looks really dusty for some reason???? I think because I was sanding it maybe lol. This is still made to fit on the Kabbit body but should fit similarly sized dolls, but it's also meant to be a smaller head in general. I'll take some more pics of it on the body, but I'm waiting for some new magnets to arrive. They should be here later today.

[everydaydollydomes]

My Drizzle head is finally all set! It's available through either my Ko-fi or my Cults3D page.

I've adjust the size a bit so it's not quite so big and heavy and the magnet wells. It takes an 8x2mm magnet but so long as it's no thicker than 2mm, you can use a smaller diameter magnet.

I'll be bringing this head to Resin Rose, too, to sell.

[everydaydollydomes]

Brewnhilda is 99.9% finished. The altheadcap is a smidge thin where the magnets are so I'm just gonna thicken that up a little and we're gonna add a little texture there to really sell the 'cup of tea/coffee' vibe. It otherwise smoothed out really beautifully. I should be able to put the files up sometime tomorrow night hopefully.

[everydaydollydomes]

I'm on fire today~! Hyperfixation in full swing :p Gogo was one of the ones I started early on in my modeling process so they've been sitting in the WIP a while and just got a bit buried under other projects. It's a bit snug in the headcap, but should fit the typical s-hooks I suggest for the heads I make. I was hoping to have all three eyes open, but due to the size/placement, the green light needed to remain closed off - the placement of the neck joint made an eyechip sort of awkward; it would have needed the back kind of sliced awkwardly. That is something I can offer as an alternative if there's interest, though.

One of my friends has offered to test print both of Deejay and Static so I may have them available for Resin Rose.

I am also considering offering to print for people who want a print of the heads I make/what Kabbit files I have access to.

[everydaydollydomes]

I have been....very busy today.

Colors are just for reference.