#self-watering

[touchmycoat]

NEXT PROJECT

[naturecpw]

DIY Self-Watering Planters | eHow.com

By Jonathan Fong - Jul 1, 2021 Jonathan Fong is the host of "Style with a Smile" on YouTube and the author of "Parties that Wow," "Flowers that Wow" and "Walls that Wow."

There's an easier, more reliable way to water your plants. These self-watering planters provide a constant supply of moisture, and they're so simple to make with used plastic soda bottles.

👇

👉 https://www.ehow.com/13766949/diy-self-watering-planters

👆

If your thumb is anything but green, join the club. Watering indoor plants, as easy as that might sound, just isn't one of my strengths. I forget to water them, and then when I do remember, I over-water to compensate. Fortunately, there's an easier, more reliable way to water your plants. These self-watering planters provide a constant supply of moisture, and they're so simple to make with used plastic soda bottles. Your plants will definitely thank you.

Things You'll Need

Plastic soda bottle

Hobby knife

Drill

T-shirt scrap

Scissors

Toothpick

Potting soil mix

Seeds or plants

Step 1: Cut a Plastic Soda Bottle in Two With a hobby knife, cut a clean, empty plastic soda bottle crosswise in half. I used a 1.25-liter bottle. The bottle does not need to be cut exactly in half. Plastic bottles usually have grooves in them, so I followed along one of the grooves right under the label to cut a straight line. You'll now have two sections: the top half with the bottle cap and the bottom half. Remove the label from the top section if you wish.

Step 2: Smooth the Edge of the Cut Bottle The top section with the bottle cap will be the top of the planter except it will be inverted. Let's smooth the edge where it was cut so it's not so sharp. To do this, heat a pan on the stove for a few minutes. Then, turn over the pan and hold this section of the bottle against the pan to smooth it out. This technique gives you a nice, finished edge.

Step 3: Drill a Hole in the Bottle Cap Drill a small hole in the bottle cap. I used a 7/32 drill bit.

Step 4: Cut a Strip of T-Shirt Fabric Cut a strip of a white cotton T-shirt to about 1 by 8 inches.

Step 5: Thread the Fabric Through the Hole Thread the strip of T-shirt fabric through the hole in the bottle cap. It helps to use a toothpick to push the fabric through. Then, screw the bottle cap back onto the bottle.

Step 6: Drill Holes in the Bottom Section The bottom half of the soda bottle will be the water reservoir. Drill four to five small holes in this section for air holes. I used a 7/64 drill bit. Make sure these holes are above the intended water line.

Step 7: Fill the Planter With Soil Fill the planter (the section with the bottle cap on the bottom) with soil. If you are planting seeds, you'll fill it to the top with soil. If you are transplanting, then only fill it part way to accommodate the plant. Make sure the cotton T-shirt strip extends to the top of the soil rather than getting buried at the bottom.

Step 8: Add the Plant If you are transplanting, add the plant on top of the soil already in the planter. Three-inch potted plants fit perfectly in a 1.25-liter bottle.

Step 9: Fill the Water Reservoir Add water to the bottom section of the plastic bottle, making sure you don't fill it above the air holes. Then, drop the planter into the water reservoir so the fabric strip sits in the water. Water now travels from the reservoir into the soil as needed. These self-watering planters are particularly helpful if you're going to be out of town for a few days and don't have someone to water your plants. Plus, they look quite elegant despite their humble origin as soda bottles.

[hqcreations]

Self-Watering Grow System

I learned a new technique while volunteering at a community garden!  This grow system is an cheap and efficient technique to keep container plants hydrated. In this example, a hole was created at the bottom of a plastic bucket, large enough to hold a red party cup at its rim. The cup itself has holes that is submerged in a water well created by a plastic sheeting over a 4-sided wooden trough. The plant gradually and slowly wicks water from the submerged red cup. The peppers and corn are doing quite well, but we’re also testing out parsnips and beets. Fingers crossed!

[shadesofmauve]

I’m seriously considering trying to turn my second whiskey barrel into a self-irrigating planter (SIP). I have all the tools except for a hole saw (if it turns out I need a hole saw) and dad has that. I’ll have a car over the weekend, so I can get stuff! And I have to take the soil out of that planter anyway so I can move it without breaking my back.

I mean, I need another project like I need another hole in the head, but theoretically it’s labor-saving down the line and squash and tomatoes love it. 

I just need to figure out what to use for the basin underneath and the support for the soil, since plastic tubs are usually square. One tutorial I saw, for a larger bed, used flexible pond liner, which seems like a neat idea -- it lets use use the maximum available space for water.

Huh. I wonder if I have any 6 mil plastic left over from remodeling...

Really, the only thing that I don’t like about the SIP idea is how much plastic is used. I’d love to get away from so much plastic. But these are all hard-wearing, non-disposable plastic uses (at least theoretically), so that’s alright, I suppose.

[outragedtortilla]

K I need a self-watering compost-baking planter for my plants thanks bye.

TIME CAPSULE & DAILY WRITING PROMPTS & PLEASE MAKE THIS HAPPEN SCIENCE

[ramyeonpng]

self-watering vessel

[outragedtortilla]

been looking into terracotta self-watering systems lately also

[robinson7ema]

Looking for a perfect ornament for your home, but also want it to be nice and useful? An ideal thing for you is the Glowpeer planter that offers an extra modern look and is self-watering and does not require anything from you!